Search results
501
Case study
Force d'extraction d'un briquet - Sécurité enfant
Exigence
Le client fabrique des briquets et développe actuellement u
502
Case study
Écrasement des comprimés pharmaceutiques et résistance à la rupture
Exigence
De nombreux produits se présentent sous forme de comprimés, avec une durabilité conçue à la fois pour l'emballage et son utilisation.
503
Case study
Résistance à la flexion des tapis composites à base de ciment géosynthétique
Exigence
Concrete Canvas Ltd. utilise la technologie des matériaux de pointe dans son produit Concrete Canvas® GCCM, qui est essentiellement du béton sur rouleau.
505
Case study
Tea bag integrity
Customised engineering example
Some of the simplest applications may not seem so obvious when you face them. A string and tab on a tea bag?
506
Case study
Essai de pelage avec accessoire de préhension à vide et rotatif
Exigence
Des tests sont nécessaires pour une gamme de barquettes en plastique flexible de même dimension mais de formes différentes, contenant des biscuits et des confiseries.
507
Case study
Force d'application et de retrait de bouchon de conteneur de fluide industriel
Exigence
L'entreprise de conception recherchait un système nécessaire pour mesurer la force de comrpession et la force de retrait d'un bouchon moulé par injection sur une nouvelle fabrication de bidon d'huile.
508
Case study
Sports shoe cleats release torque
Requirement
A leading golf shoe supplier needed to measure the release torque of the interchangeable cleats in its range of sports footwear.
509
Case study
Utilisation d'un UTM comme outil d'étalonnage pour les capteurs de force
Exigence
Lorsqu'il s'agit de configurer et d'étalonner une capteur de force en traction et en compression, cela peut prendre du temps, en particulier lorsque les charges concernées sont trop élevées pour utiliser un ensemble de poids
510
Case study
Tests de couple pour vérification de dosage des inhalateurs-doseurs, les auto-injecteurs et les stylos à insuline
Exigence
Il va sans dire que l'administration et la dose correctes de médicament sont essentielles pour garantir les meilleures chances de rétablissement et de bien-être des patients.
511
Accessory
Assisted Pull-Peel Table 90 Degree, 500 N
432-051
The Assisted Pull-Peel table is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of the peel table is directly…
512
[Page extract]
Industry
Mecmesin is an expert in the design and manufacture of force, materials and torque testing equipment, with over 40 years’ dedicated experience in the field.
513
Accessory
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
514
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
515
Accessory
Rotating Crimp Receptacle (RCR), 1 kN, 10-32 UNF and 5-16 UNC
432-379
Rotating Crimp Receptacle (RCR)
A versatile crimp termination holder that accommodates a wide range of terminal sizes.
The inner slotted ring rotates to fit up to 8 different-sized crimp terminals. The shoulder of the terminal rests against the inner…
516
Accessory
FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws
432-642
Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair.
A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…
517
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
518
Accessory
Lower Key-operated Chuck, small, round shaft, fits Vortex spindle
432-496
Lower ‘key-operated’ 4-jaw Chuck (small)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
519
Accessory
Digital I/O simulator plug
432-663
The 25-pin Digital I/O Simulator Plug is inserted into the I/O port of any Emperor-controlled Mecmesin test stand. By routing digital outputs to inputs, it allows the user to create test programmes in Emperor software with an added layer of sophistication…
521
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
522
Accessory
Extended Peg Hook, 50 N, 10-32 UNF
432-181
The extended peg hook is supplied fitted to a short chain link assembly having a 10-32 UNF female thread. It is used for gripping clothing attachments with a loop, e.g. a bow, when carrying out pull-off "test-to-failure" tests.
Typically used in…
523
Accessory
Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF
432-413
The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards.
A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…
524
Accessory
Lower Keyless Chuck, large, round shaft, fits Vortex spindle
432-445
Lower ‘keyless’ 4-jaw Chuck (large)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected.
Used for holding…
525
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat