Search results
326
Accesorio
Button Pull-off Fixture, 500 N, 10-32 UNF
432-175
Used to test the security of buttons and other textile attachments. The slotted button pull fixture has interchangeable plates for different sizes of shank (3, 5 and 7 mm), and a shatter-protection guard.
Connects to loadcell and used with a motorised…
327
Accesorio
Lower Key-operated Chuck, small, round shaft, fits Vortex spindle
432-496
Lower ‘key-operated’ 4-jaw Chuck (small)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
328
Accesorio
Assisted Pull-Peel Table 90 Degree, 500 N
432-051
The Assisted Pull-Peel table is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of the peel table is directly…
329
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
331
Accesorio
FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws
432-642
Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair.
A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…
332
Accesorio
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
333
Caso de estudio
Rotary damper gear precision torque characteristics
Requirement
A global manufacturer and distributor of component parts that are used in products across many industries including transport, beauty, consumer goods and healthcare, came to Mecmesin with a challenging torque measurement applicatio
334
[Page extract]
bursting strength (sheet rupture)
Bursting strength is the capacity of a material or product to maintain in continuity when subjected to pressure.
335
Caso de estudio
Thermostatic Radiator Valve (TRV) operational torque
Requirement
In the drive to continue to be class-leading in quality, durability and customer satisfaction, the New Product Development (NPD) department sought to leverage their expertise in the subjective assessment of the optimal tactile chara
336
Caso de estudio
Pruebas de tracción de prótesis de hombro
Requisito Keith Borowsky, eminente cirujano ortopédico de la Facultad de Medicina de la Universidad de Brighton, está desarrollando una nueva prótesis ortopédica para la reconstrucción del hombro.
337
Software
VectorPro Lite force motorised stand
VectorPro® Lite software
Available as an optional extra to Mecmesin’s motorised force testers, VectorPro Lite is an advanced data acquisition and plotting software package. Call-up pre-stored test routines for tensile and compression testing, present test…
339
Caso de estudio
Plastic styled motor fluid container land surface seal adhesive peel
Requirement
Bullsone is Korea’s leading manufacturer of auto care products. They offer a wide range of cleaning and preserving products for components used in vehicle exterior and interior body trim.
340
Caso de estudio
Headset microphone joint torque
Requirement
Jabra is a subsidiary of GN Netcom and is a global manufacturer of innovative headsets (wireless and corded) and speakerphone solutions.
341
[Page extract]
BS 5G 178-1
Provides updated tests and test requirements for crimped joints with copper, copper alloy, aluminium and aluminium alloy conductors.
342
Caso de estudio
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
343
Event
T-Peel (Adhesion Strength) Testing
This webinar will focus on the most common approach to measuring the adhesion strength of two materials bonded together with an adherent.
344
Caso de estudio
Peel test of semi-rigid packaging for medical device
Customised engineering example
Our client needed to test the peeling quality of a Tyvek® paper lid used to seal a sterile, semi-rigid thermoformed plastic tray containing pre-filled syringes.
345
Bundle
Catalyst tester for ASTM D4189 and ASTM D6175
OmniTest 2.5
BD002
Catalyst crush strength tester, configured for key international test standards including ASTM D4179 and ASTM D6175.
346
Event
Live Demonstration: Face mask strength testing & Syringe plunger breakaway force testing
Medical device testing ensures patient safety, regulatory compliance, performance, quality, usability, claims examination, and post-market safety.
347
Caso de estudio
Seed bottle closure torque testing
Requirement
The Royal Botanic Gardens, Kew, have undertaken an international conservation initiative to preserve seed specimens of over 24,000 plant species, protecting them from extinction at the Millennium Seed Bank at Wakehurst Place, West
348
Caso de estudio
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
349
Caso de estudio
Screw torque of pump dispensers
Requirement
Pfeiffer, based in Germany, are a leading manufacturer of atomisers and dosing systems for the pharmaceutical and cosmetics industries.
350
Caso de estudio
Train door closing pinch force tester
Requirement
South West Trains required a system to measure the closing force (pinch) of their external flush fitting train doors.