Search results
326
Accessory
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
327
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
328
Accessory
Rotating Crimp Receptacle (RCR), 1 kN, 10-32 UNF and 5-16 UNC
432-379
Rotating Crimp Receptacle (RCR)
A versatile crimp termination holder that accommodates a wide range of terminal sizes.
The inner slotted ring rotates to fit up to 8 different-sized crimp terminals. The shoulder of the terminal rests against the inner…
329
Accessory
FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws
432-642
Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair.
A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…
330
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
331
Accessory
Lower Key-operated Chuck, small, round shaft, fits Vortex spindle
432-496
Lower ‘key-operated’ 4-jaw Chuck (small)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
333
Accessory
Digital I/O simulator plug
432-663
The 25-pin Digital I/O Simulator Plug is inserted into the I/O port of any Emperor-controlled Mecmesin test stand. By routing digital outputs to inputs, it allows the user to create test programmes in Emperor software with an added layer of sophistication…
334
Accessory
Extended Peg Hook, 50 N, 10-32 UNF
432-181
The extended peg hook is supplied fitted to a short chain link assembly having a 10-32 UNF female thread. It is used for gripping clothing attachments with a loop, e.g. a bow, when carrying out pull-off "test-to-failure" tests.
Typically used in…
335
Accessory
Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF
432-413
The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards.
A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…
336
Accessory
Lower Keyless Chuck, large, round shaft, fits Vortex spindle
432-445
Lower ‘keyless’ 4-jaw Chuck (large)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected.
Used for holding…
337
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
338
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
339
Accessory
Button Pull-off Fixture, 500 N, 10-32 UNF
432-175
Used to test the security of buttons and other textile attachments. The slotted button pull fixture has interchangeable plates for different sizes of shank (3, 5 and 7 mm), and a shatter-protection guard.
Connects to loadcell and used with a motorised…
340
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
341
Case study
Rotary damper gear precision torque characteristics
Requirement
A global manufacturer and distributor of component parts that are used in products across many industries including transport, beauty, consumer goods and healthcare, came to Mecmesin with a challenging torque measurement applicatio
342
[Page extract]
bursting strength (sheet rupture)
Bursting strength is the capacity of a material or product to maintain in continuity when subjected to pressure.
343
Case study
Thermostatic Radiator Valve (TRV) operational torque
Requirement
In the drive to continue to be class-leading in quality, durability and customer satisfaction, the New Product Development (NPD) department sought to leverage their expertise in the subjective assessment of the optimal tactile chara
344
Software
VectorPro Lite force motorised stand
VectorPro® Lite software
Available as an optional extra to Mecmesin’s motorised force testers, VectorPro Lite is an advanced data acquisition and plotting software package. Call-up pre-stored test routines for tensile and compression testing, present test…
346
Case study
Plastic styled motor fluid container land surface seal adhesive peel
Requirement
Bullsone is Korea’s leading manufacturer of auto care products. They offer a wide range of cleaning and preserving products for components used in vehicle exterior and interior body trim.
347
Case study
Headset microphone joint torque
Requirement
Jabra is a subsidiary of GN Netcom and is a global manufacturer of innovative headsets (wireless and corded) and speakerphone solutions.
348
Event
T-Peel (Adhesion Strength) Testing
This webinar will focus on the most common approach to measuring the adhesion strength of two materials bonded together with an adherent.
349
Bundle
Catalyst tester for ASTM D4179 and ASTM D6175
OmniTest 2.5
BD002
Catalyst crush strength tester, configured for key international test standards including ASTM D4179 and ASTM D6175.
350
Event
Live Demonstration: Face mask strength testing & Syringe plunger breakaway force testing
Medical device testing ensures patient safety, regulatory compliance, performance, quality, usability, claims examination, and post-market safety.