Mecmesin | Search results

326

^{[Page extract]}

Industry

Mecmesin is an expert in the design and manufacture of force, materials and torque testing equipment, with over 40 years’ dedicated experience in the field.

327

Accessory

The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…

328

Accessory

FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws

432-642

Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair. A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…

329

Accessory

3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting

Mec103-cgr

MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel. The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…

330

Accessory

Rotating Crimp Receptacle (RCR), 1 kN, 10-32 UNF and 5-16 UNC

432-379

Rotating Crimp Receptacle (RCR) A versatile crimp termination holder that accommodates a wide range of terminal sizes. The inner slotted ring rotates to fit up to 8 different-sized crimp terminals. The shoulder of the terminal rests against the inner…

331

Accessory

Lower Key-operated Chuck, small, round shaft, fits Vortex spindle

432-496

Lower ‘key-operated’ 4-jaw Chuck (small) Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected. Used for…

332

Accessory

3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting

Mec103-cgr

333

Accessory

Digital I/O simulator plug

432-663

The 25-pin Digital I/O Simulator Plug is inserted into the I/O port of any Emperor-controlled Mecmesin test stand. By routing digital outputs to inputs, it allows the user to create test programmes in Emperor software with an added layer of sophistication…

334

Event

Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar

335

^{[Page extract]}

Manual test stands

Manual test stands allow simple force testing when budgets are limited. Lever-operated models enable rapid testing of tension and compression up to 500 N.

336

Accessory

Extended Peg Hook, 50 N, 10-32 UNF

432-181

The extended peg hook is supplied fitted to a short chain link assembly having a 10-32 UNF female thread. It is used for gripping clothing attachments with a loop, e.g. a bow, when carrying out pull-off "test-to-failure" tests. Typically used in…

337

Accessory

Lower Keyless Chuck, large, round shaft, fits Vortex spindle

432-445

Lower ‘keyless’ 4-jaw Chuck (large) Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected. Used for holding…

338

Accessory

Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF

432-413

The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards. A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…

339

Event

Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)

Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma. The smooth and consistent operat

340

Accessory

Button Pull-off Fixture, 500 N, 10-32 UNF

432-175

Used to test the security of buttons and other textile attachments. The slotted button pull fixture has interchangeable plates for different sizes of shank (3, 5 and 7 mm), and a shatter-protection guard. Connects to loadcell and used with a motorised…

341

Event

Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar

When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.

342

Case study

Rotary damper gear precision torque characteristics

Requirement A global manufacturer and distributor of component parts that are used in products across many industries including transport, beauty, consumer goods and healthcare, came to Mecmesin with a challenging torque measurement applicatio

343

^{[Page extract]}

bursting strength (sheet rupture)

Bursting strength is the capacity of a material or product to maintain in continuity when subjected to pressure.

344

Case study

Thermostatic Radiator Valve (TRV) operational torque

Requirement In the drive to continue to be class-leading in quality, durability and customer satisfaction, the New Product Development (NPD) department sought to leverage their expertise in the subjective assessment of the optimal tactile chara

345

Software

VectorPro Lite force motorised stand

VectorPro® Lite software Available as an optional extra to Mecmesin’s motorised force testers, VectorPro Lite is an advanced data acquisition and plotting software package. Call-up pre-stored test routines for tensile and compression testing, present test…

346

^{[Page extract]}

ASTM D3217

Significance and Use

347

Case study

Plastic styled motor fluid container land surface seal adhesive peel

Requirement Bullsone is Korea’s leading manufacturer of auto care products. They offer a wide range of cleaning and preserving products for components used in vehicle exterior and interior body trim.

348