Search results
251
Case study
Removal torque of cap from drug delivery device
Requirement
Global medical technology company Becton Dickinson (BD) needed to assess the torque required to twist off the cap of a drug delivery device.
252
Case study
Train sliding door slam force tester
Requirement
A portable device was specified for testing the force required to activate the inbuilt safety device when automatic doors close on trains.
253
Case study
Press stud popper pull-off test
Requirement
The customer was a supplier to major clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
254
Case study
Festive lighting masonry anchorage strength checking
Requirement
A number of local councils in the United Kingdom have adopted a new code of practice for the Installation, Operation and Removal of Seasonal Decorations.
255
Case study
Using a UTM as a calibration tool for loadcells
Requirement
When it comes to configuring and calibrating a loadcell in tension and compression this can be a time-consuming process, particularly when the loads concerned are too high to use a set of calibrated weights (also known as ‘masses’)
256
Case study
Geosynthetic cementitious composite mat bend strength
Requirement
Concrete Canvas Ltd. utilises ground-breaking materials technology in their Concrete Canvas® GCCM product, which is essentially concrete on a roll.
257
Accessory
Flat Crush Test Upper and Lower Plates with Modified Anvil Plate and Self-Adjusting Adapter
PDV11089
A number of test methods and standards employed by various industry bodies call upon specific crush fixtures and associated accessories to be used in conjunction with a compression tester. The Flat Crush Test fixtures support the test piece on the lower…
258
Accessory
Edge Crush Test Guide Blocks
PDV14137
A number of test methods and standards employed by various industry bodies call upon specific crush fixtures and
associated accessories to be used in conjunction with a compression tester. The Edge Crush Test Guide Blocks support the test piece on the…
259
Accessory
Cable Cam grip for CrimpTest-1 kN
432-660
Cable Cam Grip for CrimpTest-1 Tester (supplied as standard with the Tester)
The Cable Cam Grip is designed for holding insulated cables and wire when tensile testing the pull strength of terminals up to 1 kN.
The cable is secured by the serrated cam,…
260
Accessory
25 mm/50 mm Grab Test Textile Fixture, 500 N, 10-32 UNF
432-323
The 'Grab Test' Textile Fixture has jaws of 25mm…
261
Test Frame
MultiTest test frame (twin column)
MultiTest test frame
A motorised test frame driven by twin ballscrews featuring dual-columns and designed to apply tension and compression from 2 N right up to a capacity of 50 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing…
262
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
263
[Page extract]
Torque systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers? Do you want to reduce testing time and increase throughput for operators when performing batch tests?
265
[Page extract]
ASTM E1012-12e1
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
266
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
267
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
268
Test Frame
MultiTest test frame (single column)
MultiTest test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 5 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a quality…
269
[Page extract]
Power your torque testing
Sophisticated power - easy to use
Looking for an automated torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
270
[Page extract]
Students meet the Mecmesin MultiTest
Having spent time with the Mecmesin team and seen their material testers in action, WPI opted to invest in three Mecmesin MultiTest 2.5-dV testers.
271
Case study
Lipstick shear force resistance
Requirement
Lipstick holds the top spot in the hierarchy of makeup with its ability to completely transform appearance without the help of any other beauty product.
272
Specials
UTM FAQs
FAQs
How does the OmniTest universal testing machine compare in size and portability?
The OmniTest universal testing machine (UTM) offer
273
Case study
ROPP Wine Closure Removal Torque
Requirement
The packaging of wine has great influence on the quality of the product delivered to the customer. Traditionally the method of closure has been the natural, or latterly synthetic, cork stopper.
274
Case study
Wall-mounted air freshener destructive loading evaluation
Requirement
The customer wished to apply a controlled load of 350N to a wall mounted air freshener, replicating the effect of a child standing on it. The load needed to be applied in turn to 4 different planes on the product, e.g.
275
Case study
Cap removal test of plastic vial
Requirement
The customer approached Mecmesin with a specification to pull-off the cap of a pharmaceutical phial. The test equipment needed to be simple to use and able to perform repeatable tests.