Search results
526
Accessory
Puncture Test Fixture to EN ISO 14477, 500N, QC-20 fitting
MecS511
This EN ISO 14477 Puncture Test Fixture is for testing resistance strength in flexible packaging materials.
The specimen is clamped in the lower specimen holder, which is connected to the base plate of the test stand via a QC-20 female hole.
An upper '…
527
Accessory
Interface cable, AFG/AFTI to MultiTest-dV / Vortex-dV, Stand reverse & RS232
351-092
Interface cable, AFG to MultiTest-dV (2003-April 2020)…
528
Accessory
Automated Syringe Batch Tester
PDV19179
The Automated Syringe Batch tester is a bench-top system for checking the ‘break-loose’ and ‘glide force’ of up to 12 individual syringes in one ‘load-and-run’ cycle. In the face of increased demand on production of syringes, this system enables larger…
529
Accessory
Crush Test Fixture with Precision Guide
PSV21062
Precise alignment of the upper compression plate with the test piece is essential for optimum accuracy of results. Mecmesin recommends a minimum of self-adjusting compression plates and, for ECT and RCT tests, the Crush Test Fixture featuring a Precision…
530
Test Frame
MultiTest-dV test çerçevesi
MultiTest-dV test çerçevesi 2 N'den 2,5 kN (550 lbf) kapasiteye kadar gerilim ve sıkıştırma uygulamak için tasarlanmış vidalı mil tahrikli motorlu test çerçevesi. Çok yönlü yapısı, kalite kontrol veya Ar-Ge ortamında her türlü bileşeni test etmek…
531
Case study
PPE yüz siperliklerinde köpük bandın soyulma mukavemeti
gereklilik Yüz Kalkanları (Yüz Vizörleri olarak da bilinir), COVID-19'un yayılmasını önlemeye yardımcı olmak için sağlık sektöründeki ön saflarda çalışanlar tarafından kullanılan hayati bir KKD aracıdır.
532
Case study
Ölçülü inhalerler, otomatik enjektörler ve insülin kalemleri için dozaj kontrol tork testleri
gereklilik En iyi hasta iyileşme ve refah şansını sağlamak için doğru uygulama ve uygun ilaç dozunun temel olduğunu söylemeye gerek yoktur.
534
Case study
Sports shoe cleats release torque
Requirement
A leading golf shoe supplier needed to measure the release torque of the interchangeable cleats in its range of sports footwear.
535
Case study
Endüstriyel sıvı kabı dağıtım kapağı uygulama ve çıkarma kuvveti
gereklilik Yeni bir yağ kabı tasarımından enjeksiyon kalıplı bir kapağın itme kuvvetini ve çıkarma kuvvetini ölçmek için bir sistem gerekliydi.
536
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
537
Accessory
Assisted Pull-Peel Table 90 Degree, 500 N
432-051
The Assisted Pull-Peel table is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of the peel table is directly…
538
Accessory
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
539
Accessory
Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF
432-413
The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards.
A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…
540
Accessory
Lower Keyless Chuck, large, round shaft, fits Vortex spindle
432-445
Lower ‘keyless’ 4-jaw Chuck (large)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected.
Used for holding…
541
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
542
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
543
Accessory
Digital I/O simulator plug
432-663
The 25-pin Digital I/O Simulator Plug is inserted into the I/O port of any Emperor-controlled Mecmesin test stand. By routing digital outputs to inputs, it allows the user to create test programmes in Emperor software with an added layer of sophistication…
544
[Page extract]
Industry
Mecmesin is an expert in the design and manufacture of force, materials and torque testing equipment, with over 40 years’ dedicated experience in the field.
545
Accessory
Rotating Crimp Receptacle (RCR), 1 kN, 10-32 UNF and 5-16 UNC
432-379
Rotating Crimp Receptacle (RCR)
A versatile crimp termination holder that accommodates a wide range of terminal sizes.
The inner slotted ring rotates to fit up to 8 different-sized crimp terminals. The shoulder of the terminal rests against the inner…
546
[Page extract]
sanayi
Mecmesin, 40 yılı aşkın saha tecrübesi ile kuvvet, malzeme ve tork test ekipmanı tasarımı ve üretiminde uzmandır. Doğru, güvenilir ve uygun fiyatlı test çözümleri sunmak için küresel olarak birçok sektörde çalışıyoruz.
547
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
548
Accessory
Extended Peg Hook, 50 N, 10-32 UNF
432-181
The extended peg hook is supplied fitted to a short chain link assembly having a 10-32 UNF female thread. It is used for gripping clothing attachments with a loop, e.g. a bow, when carrying out pull-off "test-to-failure" tests.
Typically used in…
549
Accessory
Lower Key-operated Chuck, small, round shaft, fits Vortex spindle
432-496
Lower ‘key-operated’ 4-jaw Chuck (small)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
550
Accessory
FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws
432-642
Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair.
A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…