Search results
826
[Page extract]
Texture testing
Terms commonly used across different food sectors to describe food attributes include hardness, tenderness, firmness, cohesiveness, springiness, stickiness etc.
827
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
828
[Page extract]
texture, compression
Compression is one of the most common texture tests, especially for food products. Typically a sample is placed on a flat surface and an upper compression platen is lowered into the sample.
829
[Page extract]
Shear
Shear testing is a very popular and valuable test method applicable to food texture analysis.
This method applies slicing or 'shearing' to the product, which replicates the action of the front incisors when food is introduced into the mouth.
830
[Page extract]
T-peel
T-peel test procedures are commonly used to measure peel strength for flexible laminates.In this test, the entire load applied is transmitted to the bond. This type of peel thus tends to provide the lowest values of any peel test
831
[Page extract]
Compressive burst
The integrity of a fluid or gas-filled container can be tested in terms of its propensity to burst.
This may involve a failure in the material by splitting, or perhaps a seal/seam gives way or even the closure can break loose.
832
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
833
Article/Campaign
Mecmesin pioneers the world’s ultimate digital force gauge
Ground-breaking VFG touchscreen force gauge
834
Accessory
Self-levelling Compression Plate Steel - 116 mm, 50 kN, QC-32 fitting
MecS223g-116
MecS223g - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates - ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
835
Accessory
Compression Plate, Hardened and Ground, 50 mm, 10-32 UNF
432-172 F95
Hardened and ground compression plates have a smooth, scratch-proof surface ideal for compression testing on samples that could damage a standard compression plate, such as springs.
50mm diameter having 10-32 UNF female thread.
836
Accessory
Compression Plate, Rubber-Faced, 50 mm, 5-16 UNC
432-219
50mm nickel-plated compression plate featuring a rubber layer, which helps to prevent damage from metal-to-metal contact during a compression test.
Fitted with 5-16 UNC female thread.
Nickel-plated compression plates are resistant to rusting.
837
Accessory
Adapter, 5 kN, 5-16 UNC to 5-16 UNC, F to F
432-293
Female-to-female Adapter
Allows a grip to be connected to a force gauge/loadcell or test stand where thread connections are different.
838
Accessory
Inverted Chisel Point, Ø 12 mm, 5 kN, 5-16 UNC
432-357
For compression testing of cylindrical or wire specimens up to 5 kN.
Specimen is located centrally within the inverted V-shape and compressed to a set distance or a break.
Fitted with a 5-16 UNC female thread for connection to loadcell
839
Accessory
Adapter, 5 kN, 5-16 UNC to M12, M to F
432-332
Male-to-female Adapter
Allows a grip to be connected to a force gauge/loadcell or test stand where thread connections are different.
840
Accessory
Self-levelling Compression Plate Steel - 116 mm, 25 kN, QC-20 fitting
MecS223k-116
MecS223k - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
841
Accessory
Compression Plate, Nickel-plated, Vented by Slots & Flat, 50 mm, 10-32 UNF
432-346
Vented compression plates are ideal for top-load/crush testing of containers such as PET bottles.
Slots in the plate allow the passage of air to ensure that air inside the bottle is not compressed thereby falsifying the true measurement of the top-load…
842
Accessory
Compression Plate, Hardened and Ground, 175 mm, 5-16 UNC
432-446
Hardened and ground compression plates have a smooth, scratch-proof surface ideal for compression testing on samples that could damage a standard compression plate, such as springs.
175mm diameter having 5-16 UNC female thread.
843
Accessory
1/2" upper chuck assembly for use on Helixa sensors (3 N.m & 6 N.m only)
432-617
A standard self-centering 3-jaw chuck with key.
It has a maximum ½" (12.7 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
844
Software
Vector OS (VFG/VFTI)
Vector OS
Our touchscreen instruments are powered by Vector OS, Mecmesin's technology platform for its latest force and torque test equipment. It delivers intuitive and customisable user interfaces, as well as advanced data acquisition and analysis.
To…
845
Accessory
Transit Case for Manual Handling/Ergonomic Kit
416-007
A foam-lined rugged metal case for the components of the advanced or basic manual handling kit. Supplied as standard with the kit, has space for: a force gauge including rechargeable batteries, mains adaptor / battery charger, gripping cradle, chain link…
846
Accessory
MDD Horizontal Feet Kit
432-126
Feet for the horizontal operation of an MDD manual test stand. Supplied as a pair.
847
Accessory
Lightweight Vice Grip - Double Action, 250 N, Opening 0-46mm, 10-32 UNF
Mec227-S46
MEC 227-S46 (body only):
A Lightweight Vice Grip providing free adjustment of both jaws, allowing them to be aligned around the central axis to accommodate tensile testing of both symmetrical and asymmetrical specimens.
Rated to 250 N in tension with…
848
Accessory
Clevis Grip (small), 500 N, M6
432-216
Small Clevis Grip fitted with female M6 thread and supplied with male grub-screw.
Used for securing odd-shaped parts for testing tensile forces below 500N.
849
Accessory
Medium Vice Grip - Single Action, 1 kN, 52 mm opening, QC-20 fitting
Mec240k-S50
MEC 240k-S50 (body only) :
A Medium Single-action Vice Grip allowing one jaw to be manualy set in a position to align a test specimen around the central axis. The other jaw is freely adjustable to mechanically clamp the specimen in place.
Rated to 1…
850
Accessory
Inverted Chisel Point - Ø 8 mm, 500 N, 10-32 UNF
432-356
For compression testing of cylindrical or wire specimens up to 500 N.
Specimen is located centrally within the inverted V-shape and compressed to a set distance or a break.
Fitted with a 10-32 UNF female thread for connection to loadcell