Search results
526
Case study
Aplicação da tampa distribuidora do recipiente de fluido industrial e força de remoção
Requerimento Foi necessário um sistema para medir a força de pressão e a força de remoção de uma tampa moldada por injeção de um novo design de lata de óleo.
528
Case study
Sports shoe cleats release torque
Requirement
A leading golf shoe supplier needed to measure the release torque of the interchangeable cleats in its range of sports footwear.
529
Accessory
Assisted Pull-Peel Table 90 Degree, 500 N
432-051
The Assisted Pull-Peel table is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of the peel table is directly…
530
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
531
[Page extract]
Suportes de teste manuais
Suportes de teste manuais permitem testes de força simples quando os orçamentos são limitados.
532
Accessory
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
533
Accessory
Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF
432-413
The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards.
A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…
534
Accessory
Lower Keyless Chuck, large, round shaft, fits Vortex spindle
432-445
Lower ‘keyless’ 4-jaw Chuck (large)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 80mm depending on jaws selected.
Used for holding…
535
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
536
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
537
Accessory
Digital I/O simulator plug
432-663
The 25-pin Digital I/O Simulator Plug is inserted into the I/O port of any Emperor-controlled Mecmesin test stand. By routing digital outputs to inputs, it allows the user to create test programmes in Emperor software with an added layer of sophistication…
538
[Page extract]
Industry
Mecmesin is an expert in the design and manufacture of force, materials and torque testing equipment, with over 40 years’ dedicated experience in the field.
539
Accessory
Rotating Crimp Receptacle (RCR), 1 kN, 10-32 UNF and 5-16 UNC
432-379
Rotating Crimp Receptacle (RCR)
A versatile crimp termination holder that accommodates a wide range of terminal sizes.
The inner slotted ring rotates to fit up to 8 different-sized crimp terminals. The shoulder of the terminal rests against the inner…
540
Accessory
Extended Peg Hook, 50 N, 10-32 UNF
432-181
The extended peg hook is supplied fitted to a short chain link assembly having a 10-32 UNF female thread. It is used for gripping clothing attachments with a loop, e.g. a bow, when carrying out pull-off "test-to-failure" tests.
Typically used in…
541
Accessory
3- & 4-point Bend Jig, 50 kN, Steel, QC-32 fitting
Mec103-cgr
MEC103 - A compact yet fully-configurable 50 kN Bend Jig in steel.
The main support beam attaches to the base of the test frame and has a bending span up to 120 mm. It can accept a wide selection of interchangeable single-roller or dual-roller anvils to…
542
Accessory
Lower Key-operated Chuck, small, round shaft, fits Vortex spindle
432-496
Lower ‘key-operated’ 4-jaw Chuck (small)
Fitted with a round shaft for connection to the motor spindle of 'Vortex' motorised test stands. Supplied with 3 different sets of interchangeable jaws. Max.opening 50mm depending on jaws selected.
Used for…
543
Accessory
FPT T-Peel Vice-Grips (pair) fitted with 25 mm rubber jaws
432-642
Double-action vice grips with rubber-faced jaws, typically for peel-testing on the FPT-H1 horizontal tester. 8 mm QC fitting. Sold as a pair.
A Lightweight Single-action Vice Grip used for peel and delamination testing of pressure-sensitive adhesives…
544
[Page extract]
Indústria
A Mecmesin é especialista no projeto e fabricação de equipamentos de teste de força, materiais e torque, com mais de 40 anos de experiência dedicada no campo.
545
Accessory
Button Pull-off Fixture, 500 N, 10-32 UNF
432-175
Used to test the security of buttons and other textile attachments. The slotted button pull fixture has interchangeable plates for different sizes of shank (3, 5 and 7 mm), and a shatter-protection guard.
Connects to loadcell and used with a motorised…
547
Case study
Rotary damper gear precision torque characteristics
Requirement
A global manufacturer and distributor of component parts that are used in products across many industries including transport, beauty, consumer goods and healthcare, came to Mecmesin with a challenging torque measurement applicatio
548
[Page extract]
bursting strength (sheet rupture)
Bursting strength is the capacity of a material or product to maintain in continuity when subjected to pressure.
549
Case study
Thermostatic Radiator Valve (TRV) operational torque
Requirement
In the drive to continue to be class-leading in quality, durability and customer satisfaction, the New Product Development (NPD) department sought to leverage their expertise in the subjective assessment of the optimal tactile chara
550
Case study
Projeto e fabricação de molas
Requerimento A Longcroft Engineering projeta e fabrica molas, desde protótipos e designs personalizados feitos à mão até a produção em alto volume.