Search results
1376
[Page extract]
IEC 60371-2
Part 1 is definitions of general requirements
Part 3 specifications for individual materials
A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.
1377
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
1378
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
1379
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
1380
[Page extract]
ASTM D3914
ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.
1381
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
1382
[Page extract]
BS EN 1492-1
Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web
1383
[Page extract]
ASTM D5656-10
This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.
1384
[Page extract]
BS EN 50289-3-17
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths
1385
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
1386
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
1387
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
1388
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1389
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1390
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
1391
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
1392
[Page extract]
ISO 594-2
ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.
1393
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
1394
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
1395
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
1396
[Page extract]
BS EN ISO 11608-3
Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions
1397
[Page extract]
BS EN 12316-1
Waterproof materials, Sheet materials, Flexible materials, Peel resistance, Peeling tests, Joints, Bitumens, Bituminous products, Roof coverings, Test equipment, Specimen preparation
1398
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
1399
[Page extract]
BS EN 12346
Gymnastics equipment, Wall bars, Ladders, Sports equipment, Indoor sports equipment, Design, Dimensions, Height, Dimensional tolerances, Shape, Strength of materials, Safety measures, Marking, Instructions for use, Equipment safety, Mechanical testing,