Mecmesin | Search results

1401

^{[Page extract]}

BS EN ISO 376

BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.

1402

^{[Page extract]}

ASTM D5656-10

This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.

1403

^{[Page extract]}

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1404

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1405

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1406

^{[Page extract]}

ASTM D6195-03

These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.

1407

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1408

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1409

^{[Page extract]}

ASTM D7834-13

During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.

1410

^{[Page extract]}

SAE J174

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.

1411

^{[Page extract]}

ASTM D5766 / D5766-M

ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.

1412

^{[Page extract]}

ASTM B913

This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.

1413

^{[Page extract]}

BS EN 1465

Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.

1414

^{[Page extract]}

ASTM D7137 / D7137M-17

ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation

1415

^{[Page extract]}

ASTM D1871

This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.

1416

^{[Page extract]}

ASTM D380

ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.

1417

^{[Page extract]}

ISO 8510-1

Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.

1418

^{[Page extract]}

BS EN 1393

BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.

1419

^{[Page extract]}

BS EN ISO 8670-2

Two part test on filled bags: 1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate

1420

^{[Page extract]}

ASTM D2659

ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.

1421

^{[Page extract]}

ISO 594-2

ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.

1422

^{[Page extract]}

PSTC 8

Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape. The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.

1423

Case study

稳定的弹簧测试

定制工程实例我们的客户需要在压缩状态下测试许多小型轻质弹簧。为避免弹簧弯曲和侧向移动，需要支撑主轴或导向杆。 Mecmesin设计并提供了带有导杆的压缩探头，以精确测试被测弹簧的尺寸。与我们的软件控制的MultiTest支架一起使用时，它们可以快速插入弹簧并进行高度可重复的测试。

1424

^{[Page extract]}

FINAT FTM2

This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.

1425

^{[Page extract]}

BS EN ISO 11608-3

Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions