Search results
851
[Page extract]
BS EN ISO 8510-2
Adhesives, Adhesive-bonded joints, Adhesion tests, Flexible materials, Peeling tests, Test equipment, Specimen preparation, Test specimens
852
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
853
[Page extract]
ASTM F963-17
This specification relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a toy is intended or after reasonably foreseeable abuse.
854
[Page extract]
BS EN 2307
Ropes, Fibre ropes, Mechanical testing, Tensile testing, Dimensional measurement, Rope pitch, Elongation, Breaking load, Physical testing, Water-resistance tests, Mass, Linear density, Density measurement
855
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
856
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
857
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
861
[Page extract]
Texture testing
Terms commonly used across different food sectors to describe food attributes include hardness, tenderness, firmness, cohesiveness, springiness, stickiness etc.
862
[Page extract]
Fastening torque
Bolts and screws secure many constructions, and the equal integrity and performance of each is crucial.
863
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
864
[Page extract]
Shear
Shear testing is a very popular and valuable test method applicable to food texture analysis.
This method applies slicing or 'shearing' to the product, which replicates the action of the front incisors when food is introduced into the mouth.
865
[Page extract]
texture, compression
Compression is one of the most common texture tests, especially for food products. Typically a sample is placed on a flat surface and an upper compression platen is lowered into the sample.
866
[Page extract]
Compressive burst
The integrity of a fluid or gas-filled container can be tested in terms of its propensity to burst.
This may involve a failure in the material by splitting, or perhaps a seal/seam gives way or even the closure can break loose.
867
[Page extract]
T-peel
T-peel test procedures are commonly used to measure peel strength for flexible laminates.In this test, the entire load applied is transmitted to the bond. This type of peel thus tends to provide the lowest values of any peel test
868
[Page extract]
puncture resistance
Puncture resistance is a function of controlled stretch and tear at a point.
869
[Page extract]
Compression testing
Compression testing is a way of determining how something will react when it is squashed, or when a force is applied to it in compression.
It is performed to:
870
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
871
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
872
Case study
橡胶垫片的拉伸试验
要求英国垫片是垫片,密封产品和模制品的主要制造商。它们由多种材料制成,适合各种应用。 British Gaskets需要一个测试系统,以确保橡胶和聚合物材料的氯丁橡胶,Viton,EPDM和有机硅满足其质量控制标准并适合用途。
873
Article/Campaign
Mecmesin pioneers the world’s ultimate digital force gauge
Ground-breaking VFG touchscreen force gauge
874
Page
迈菱仪器仪表中国官网
始于1977年,英国进口
Mecmesin 系欧洲力学,材料和扭矩试验机制造商的领跑者,40 多年来与全球 50000 多家客户合作研发优质的测试解决方案,并提供价格实惠的拉力机和扭矩仪。
875
Accessory
Compression Plate, Hardened and Ground, 50 mm, M6
432-197
Hardened and ground compression plates have a smooth, scratch-proof surface ideal for compression testing on samples that could damage a standard compression plate, such as springs.
50mm diameter having M6 female thread.