Mecmesin | Search results

1401

^{[Page extract]}

BS EN 12467

Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio

1402

^{[Page extract]}

Consumer Products

Mecmesin test solutions for products typically found in the home ...

1403

Event

Wine & Spirits Capping: Cork Pull & Twist Caps

Wine packaging has a great influence on the quality of the product delivered to the customer.

1404

^{[Page extract]}

ASTM D5656-10

This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.

1405

^{[Page extract]}

ASTM D3914

ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.

1406

^{[Page extract]}

BS EN ISO 376

BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.

1407

^{[Page extract]}

ASTM D7834-13

During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.

1408

^{[Page extract]}

ASTM D1995

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1409

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1410

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1411

^{[Page extract]}

ASTM D6195-03

These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.

1412

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1413

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1414

^{[Page extract]}

ASTM D7264 / D7264M-15

ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:

1415

^{[Page extract]}

SAE J174M

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.

1416

^{[Page extract]}

BS EN 1492-1

Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web

1417

^{[Page extract]}

ASTM F607-03

The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.

1418

^{[Page extract]}

BS EN 50289-3-17

Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths

1419

^{[Page extract]}

ISO 1926

ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.

1420

^{[Page extract]}

Three flavours of confectionery test

What makes the confectionery sector’s products particularly sensitive to ingredient substitutions?

1421

^{[Page extract]}

ASTM D2979

This test method covers measurement of the pressure-sensitive tack of adhesives.

1422

^{[Page extract]}

BS 2782-12: 1210A to C

BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.

1423

^{[Page extract]}

ASTM D2148

ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).

1424

^{[Page extract]}

ISO 8113

ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.

1425

^{[Page extract]}

BS EN 12814-1

BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.