Mecmesin | Search results

901

^{[Page extract]}

ISO 2409

Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.

902

^{[Page extract]}

ASTM D6117-18

ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:

903

^{[Page extract]}

ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com

904

^{[Page extract]}

BS ISO 6133

BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.

905

^{[Page extract]}

BS EN ISO 9626

This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.

906

^{[Page extract]}

ASTM D2095

This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.

907

^{[Page extract]}

BS EN 2243-1

Air transport engineering, Adhesives, Metals, Lapped joints, Adhesion tests, Shear testing, Mechanical testing, Test specimens

908

^{[Page extract]}

BS EN 2243-4

Air transport engineering, Adhesives, Metals, Aluminium alloys, Cellular materials, Tensile testing, Adhesion tests, Test specimens, Specimen preparation, Testing conditions

909

^{[Page extract]}

ASTM D3577

1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.

910

^{[Page extract]}

ASTM D5868-01

Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which

911

Case study

Lực tác động của bộ phân phối bơm

Yêu cầu Khách hàng sản xuất một loạt các máy bơm pha chế cho ngành mỹ phẩm và chăm sóc sắc đẹp. Một yêu cầu đã được xác định để đo lực tác động của cụm máy bơm và lực kéo ra của tay cầm máy bơm.

912

^{[Page extract]}

ASTM D1578

Significance and Use Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.

913

^{[Page extract]}

BS EN 1707

Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,

914

^{[Page extract]}

ASTM D4179

1.1 This test method covers determining the resistance of formed catalysts and catalyst carriers to compressive force and is applicable to regular catalyst shapes such as tablets and spheres.

915

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

916

^{[Page extract]}

ASTM D4255 / D4255M-15a

ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.

917

^{[Page extract]}

IEC 61730-2

The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.

918

Case study

Electrical connector insertion and withdrawal forces

Customised engineering example Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.

919

^{[Page extract]}

BS 6965-1

Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard

920

^{[Page extract]}

BS EN 61238-1

Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T

921

Page

You have been subscribed to the Mecmesin newsletter

Thank you

We hope you enjoy the regular updates on our developments in force, materials and torque testing.

922

^{[Page extract]}

BS EN 61067-2

Glass fibres, Polyesters, Woven fabrics, Tape, Tape yarns, Filament (textile fibre), Polyester fibres, Textile glass, Dimensional changes, Shrinkage tests, Tensile strength, Test specimens, Testing conditions, Test equipment

923

^{[Page extract]}

ASTM F152-95

ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.

924

Case study

Smoke grenade canister integrity

Customised engineering example A manufacturer of smoke grenades required a means of testing the cap pull-off strength. The particular challenge was to grip the smooth metal cylinder for up to 5 kN of pulling force.

925

^{[Page extract]}

ISO 12625-5

ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.