Search results
1526
[Page extract]
Vice grip (Mechanical)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
1527
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
1528
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
1529
Event
Webinar: Rice Texture Analyzer (Thai) - เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
หนึ่งในปัจจัยที่สําคัญที่สุด ซึ่งมีผลต่อความสำเร็จของผลิตภัณฑ์ข้าวคือ เนื้อสัมผัส
เนื้อสัมผัสของข้าวส่งผลโดยตรงต่อความพึงพอใจของผู้บริโภค และความน่าเชื่อถือของผู้ผลิตข้าว นั่นคือเหตุผลว่า
1530
[Page extract]
ASTM F1995-12
This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.
1531
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
1532
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
1533
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
1534
[Page extract]
ISO 15509
Gives a test method for measuring the shear and/or tensile strength of an adhesively bonded plastic/plastic specimen of a specific design. This method allows the determination of a combined shear and tensile behaviour of the bond.
1535
[Page extract]
ISO 9727-5
Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.
1536
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
1537
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
1538
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
1539
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1540
[Page extract]
CETIE Guide 18
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
1541
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
1542
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
1543
[Page extract]
ASTM D6004-04
This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.
1544
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
1545
[Page extract]
ASTM F2256-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
1547
[Page extract]
ASTM D3575
ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.
1548
[Page extract]
ASTM D5458-95
This test method measures cling between two layers of film, in both a stretched and unstretched condition.
1549
[Page extract]
*corp Ikea IOS-TM-0057
This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations
1550
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.