Search results
1126
[Page extract]
BS EN 14372
This document establishes minimum safety requirements and specifies appropriate test methods for children’s cutlery and feeding utensils designed for the use of children aged up to 3 years, with or without parental supervision.
1127
[Page extract]
BS EN 2307
Ropes, Fibre ropes, Mechanical testing, Tensile testing, Dimensional measurement, Rope pitch, Elongation, Breaking load, Physical testing, Water-resistance tests, Mass, Linear density, Density measurement
1128
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
1129
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1130
Case study
Tıbbi keskinlik kutusu delinme direnci
Özel mühendislik örneği Uluslararası standartlar (ASTM F2132, BS 7320), tıbbi sivri uçlu kapların delinme direncini belirtir.
1131
[Page extract]
ASTM F963-17
This specification relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a toy is intended or after reasonably foreseeable abuse.
1132
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1135
[Page extract]
Fastening torque
Bolts and screws secure many constructions, and the equal integrity and performance of each is crucial.
1136
[Page extract]
Texture testing
Terms commonly used across different food sectors to describe food attributes include hardness, tenderness, firmness, cohesiveness, springiness, stickiness etc.
1137
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
1138
[Page extract]
Shear
Shear testing is a very popular and valuable test method applicable to food texture analysis.
This method applies slicing or 'shearing' to the product, which replicates the action of the front incisors when food is introduced into the mouth.
1139
[Page extract]
texture, compression
Compression is one of the most common texture tests, especially for food products. Typically a sample is placed on a flat surface and an upper compression platen is lowered into the sample.
1140
[Page extract]
T-peel
T-peel test procedures are commonly used to measure peel strength for flexible laminates.In this test, the entire load applied is transmitted to the bond. This type of peel thus tends to provide the lowest values of any peel test
1141
[Page extract]
Compressive burst
The integrity of a fluid or gas-filled container can be tested in terms of its propensity to burst.
This may involve a failure in the material by splitting, or perhaps a seal/seam gives way or even the closure can break loose.
1142
[Page extract]
puncture resistance
Puncture resistance is a function of controlled stretch and tear at a point.
1143
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
1144
[Page extract]
Compression testing
Compression testing is a way of determining how something will react when it is squashed, or when a force is applied to it in compression.
It is performed to:
1145
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1146
Article/Campaign
Mecmesin pioneers the world’s ultimate digital force gauge
Ground-breaking VFG touchscreen force gauge
1147
Accessory
Clevis Grip (Large), 2.5 kN, 5-16 UNC
432-400
Large Clevis Grip fitted with female 5-16 UNC thread and supplied with male grub-screw.
Used for testing heavy duty tension springs or for securing odd-shaped parts up to 2.5 kN capacity.
1148
Accessory
Flip Cap Accessory, 100 N, 10-32 UNF
432-419
The Flip Cap Accessory is designed to easily fit under flip caps to test their opening force.
It is fitted with a 10-32 UNF female thread and supplied with a male grub-screw for easy connection to a loadcell or force gauge.
1149
Accessory
Self-levelling Compression Plate Steel - 116 mm, 50 kN, QC-32 fitting
MecS223g-116
MecS223g - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates - ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
1150
Accessory
Inverted Chisel Point, Ø 12 mm, 5 kN, 5-16 UNC
432-357
For compression testing of cylindrical or wire specimens up to 5 kN.
Specimen is located centrally within the inverted V-shape and compressed to a set distance or a break.
Fitted with a 5-16 UNC female thread for connection to loadcell