Search results
1601
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
1602
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
1603
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
1604
[Page extract]
BS EN 50289-3-17
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths
1605
[Page extract]
ASTM D2148
ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).
1606
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
1607
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
1608
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
1609
[Page extract]
BS EN 1393
BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1610
[Page extract]
ASTM D5656-10
This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.
1611
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
1612
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
1613
[Page extract]
ASTM D3914
ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.
1614
[Page extract]
ISO 8627
Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.
1615
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
1616
[Page extract]
ISO 8510-1
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.
1617
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1618
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.
1619
[Page extract]
ISO 7810
Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.
1620
[Page extract]
ASTM D1995
These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and
1621
[Page extract]
BS EN 14704-1
Methods for testing using stripsof fabric in straight strip form or loops, which can be used to measure elasticity and related properties of fabrics, excluding narrow fabrics.
1623
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
1624
[Page extract]
SAE J174
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.
1625
[Page extract]
ASTM D816-06
These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from natural rubber, reclaimed rubber, synthetic elastomers, or combinations of