Mecmesin | Search results

1876

^{[Page extract]}

TAPPI T 807

This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).

1877

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

1878

^{[Page extract]}

BS EN 12209

BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.

1879

^{[Page extract]}

ASTM E855-08

This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.

1880

^{[Page extract]}

CETIE Guide 18

This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.

1881

^{[Page extract]}

ASTM D6004-04

This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.

1882

^{[Page extract]}

EN 14509

This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee CEN/TC 128. This covers a very wide range of tests including coatings, strengths etc.

1883

^{[Page extract]}

ASTM F2256-05

This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.

1884

^{[Page extract]}

EN 149

EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.

1885

^{[Page extract]}

ISO 3781

Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.

1886

^{[Page extract]}

ASTM D1004

ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.

1887

^{[Page extract]}

ASTM D5458-95

This test method measures cling between two layers of film, in both a stretched and unstretched condition.

1888

^{[Page extract]}

ASTM D3575

ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.

1889

^{[Page extract]}

ASTM C480

This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.

1890

^{[Page extract]}

ASTM D5649-01

This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.

1891

^{[Page extract]}

*corp Ikea IOS-TM-0057

This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations

1892

^{[Page extract]}

ASTM D3469

These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.

1893

^{[Page extract]}

Vice grip (Mechanical)

Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.

1894

Article/Campaign

Test title

Top-load testing solutions

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.

1895

^{[Page extract]}

*corp Ford DSEU

Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.

1896

^{[Page extract]}

ISO 527-3

ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.

1897

^{[Page extract]}

ASTM D3950

This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.

1898

^{[Page extract]}

ISO 9895

Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.

1899

^{[Page extract]}

BS EN 12311-2

BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.

1900

^{[Page extract]}

BS ISO 7322

This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells