Mecmesin | Search results

1851

^{[Page extract]}

ASTM C1161

This test method covers the determination of flexural strength of advanced ceramic materials at ambient temperature. Four-point and three-point loadings with prescribed spans are the standard.

1852

^{[Page extract]}

ASTM D5467 / D5467M-97

ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.

1853

^{[Page extract]}

ASTM D3968

This test method covers the measurement of rotational torques of Type IIIA child-resistant closures as a means of monitoring normal functioning of the child-resistant package.

1854

^{[Page extract]}

ASTM F806-99a

ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.

1855

^{[Page extract]}

A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature

1856

^{[Page extract]}

Tack test

1857

^{[Page extract]}

ISO 21180

ISO 21180 specifies a test method for the determination of the maximum tensile strength of light conveyor belts.

1858

^{[Page extract]}

ASTM D1710

Among tests for electrical and dimensional (temperature) stability, includes methods for tensile characteristics.

1859

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.

1860

^{[Page extract]}

ASTM D2344 / D2344M

ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.

1861

^{[Page extract]}

ASTM D3826

ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.

1862

^{[Page extract]}

ISO 15509

Gives a test method for measuring the shear and/or tensile strength of an adhesively bonded plastic/plastic specimen of a specific design. This method allows the determination of a combined shear and tensile behaviour of the bond.

1863

^{[Page extract]}

ISO 9727-5

Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.

1864

^{[Page extract]}

ISO 9073-3

Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.

1865

^{[Page extract]}

TAPPI T 807

This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).

1866

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

1867

^{[Page extract]}

ASTM F1995-12

This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.

1868

^{[Page extract]}

BS EN 12209

BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.

1869

^{[Page extract]}

CETIE Guide 18

This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.

1870

^{[Page extract]}

EN 14509

This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee CEN/TC 128. This covers a very wide range of tests including coatings, strengths etc.

1871

^{[Page extract]}

ASTM F1575-03

Nails are a common mechanical fastener in wood structures.

1872

^{[Page extract]}

29 073-3

Textiles: test method for nonwovens; Part 3: Determination of tensile strength and elongation.

1873

^{[Page extract]}

*corp Coca-Cola SM-PR-2645

This test ensures that the column strength of non-refillable (NR) plastic bottles is sufficient to meet minimum performance specifications for vertical loading during peak load application.

1874

^{[Page extract]}

ASTM C651

This test method covers determination of the flexural strength of manufactured carbon and graphite articles using a simple beam in four-point loading at room temperature.

1875

^{[Page extract]}

ASTM D4032-08

This test method covers the determination of the stiffness of fabrics by the circular bend procedure. The method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.