Mecmesin | Search results

1751

^{[Page extract]}

IEC 60598

IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.

1752

^{[Page extract]}

Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).

1753

^{[Page extract]}

BS EN 13942

This International Standard specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for t

1754

^{[Page extract]}

BS EN 13411-3

This European Standard deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops - it applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60mm diameter conforming

1755

^{[Page extract]}

ASTM D5179-16

ASTM D5179 is a test method for determining organic coatings adhesion to a plastic substrate. It can be used to evaluate the adhesion (pull-off strength) of various coating/substrate combinations e.g. paint and varnish.

1756

^{[Page extract]}

Vice grip (Pneumatic)

Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.

1757

^{[Page extract]}

CETIE Guide 4

This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.

1758

^{[Page extract]}

ASTM D953-18

ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.

1759

^{[Page extract]}

CETIE Guide 7

This guideline applies to the screw capping of still wines with a metallic closure having a threaded plastic insert and a tamper-evident band which needs to be snapped before it can be opened. The closure is screwed and crimped during capping.

1760

^{[Page extract]}

*corp 01M-01-217

To determine the maximum force required to rupture (break) a woven fabric.

1761

^{[Page extract]}

BS EN ISO 4074

BS EN ISO 4074:2002 specifies the minimum requirements and the test methods to be used for condoms made from natural rubber latex which are supplied to consumers for contraceptive purposes and to assist in the prevention of sexually transmitted infectio

1762

^{[Page extract]}

IEC 61210

IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o

1763

^{[Page extract]}

ASTM D4475-02

ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.

1764

^{[Page extract]}

ASTM C1674

This test method covers the determination of the flexural strength (modulus of rupture in bending) at ambient conditions of advanced ceramic structures with 2-dimensional honeycomb channel architectures.

1765

^{[Page extract]}

ASTM D4501-01

This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.

1766

^{[Page extract]}

ASTM D3481

This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.

1767

^{[Page extract]}

ASTM D6415 / D6415M-06a

ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.

1768

^{[Page extract]}

ISO 14126

ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:

1769

^{[Page extract]}

Wedge grips

Wedge grips - consisting of 2 interchangeable or fixed jaws in the shape of a wedge which are secured in a metal body.

1770

^{[Page extract]}

IFI 143

This standard provides a test method for determining the torque-tension relationship on both external and internal threaded fasteners for the purpose of measuring the frictional characteristics of the threaded fasteners.

1771

^{[Page extract]}

ISO 10373-1

ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.

1772

^{[Page extract]}

BS 6319-2

BS 6319-2 is a test method for determining the compressive strength of resin and polymer/cement compositions used in construction.

1773

^{[Page extract]}

BS EN 2243-2

This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.

1774

^{[Page extract]}

ASTM D2731

ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.

1775

^{[Page extract]}

ASTM D7249-12

This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the