Search results
1876
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
1877
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
1878
[Page extract]
SAE J 1553
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.
1879
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
1880
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
1881
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
1882
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
1883
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
1884
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1885
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
1886
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
1887
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
1888
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
1889
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1890
[Page extract]
ISO 3781
Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
1891
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
1892
[Page extract]
ASTM E405-04
These tests provide standard methods for evaluating the mechanical performance of the rotary-type window operators, while the operators are subjected to cyclic wear in opening and closing against the operating moment.
1893
[Page extract]
Transporte
Soluções Mecmesin para engenharia e design de transporte. A engenharia de transporte envolve uma complexidade enorme, combinada com os recursos mais críticos para a segurança.
1894
[Page extract]
Transport
Mecmesin solutions for transport engineering and design.
Transport engineering involves massive complexity, combined with the most stringent safety-critical features.
1895
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1896
[Page extract]
Jóias e Relógios
Na produção de joalheria e relojoaria, as ligas, componentes e outros materiais devem atender às necessidades do processo de fabricação e o produto final deve oferecer um bom desempenho de serviço quando usado pelo cliente.
1897
Software
TTT_Certify
Software TTT_Certify Gerar certificados de calibração de torque compatíveis Incluído com o TTT-300 está nosso software TTT_Certify para gerar certificados de calibração, em conformidade com os padrões ISO 17025 para ferramentas portáteis, de indicação e…
1898
Software
TTT_Certify
TTT_Certify softwareGenerate compliant torque calibration certificates
Included with the TTT-300 is our TTT_Certify software for generating calibration certificates, conforming to ISO 17025 standards for handheld, indicating and click torque tools, such…
1899
Page
Política de Privacidade
Mecmesin é um nome comercial da PPT Group UK Ltd. Sua privacidade é de grande importância para a Mecmesin e estamos comprometidos em proteger as informações pessoais que você compartilha conosco.
1900
[Page extract]
Versatility
The Vortex torque tester has been designed for versatility. Its standard configuration is rated to 10 N.m (90 lbf.in) with space to accept specimens up to 275mm wide.