Search results
976
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
977
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
978
[Page extract]
ASTM D5602/D5602M-18
An important factor affecting the performance of many membrane roofing systems is their ability to resist static puncture loads. This test method provides a means for assessing static puncture resistance.
979
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
980
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
981
[Page extract]
ISO 5628
Specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
982
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
983
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
984
[Page extract]
BS ISO 11040-4
This part of ISO 11040 applies to — tubing-glass barrels (single-chamber design) for injection preparations, and — sterilized subassembled syringes ready for filling.
985
[Page extract]
ASTM F2193-02
These specifications and test methods provide standard specifications that specify material, labeling, and handling requirements for components used in surgical fixation of the spinal skeletal system such as metallic spinal screws, spinal plates, and sp
986
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
987
[Page extract]
Flexure
Flexural or bend testing is used It is a way of determining how something will react when it is put under opposing forces across a span.to evaluate both the ductility and soundness of a material.
988
[Page extract]
double lap shear
Lap shear testing is used where an adhesive bond joins flat surfaces.
The required surfaces may be profiled, single, double or multiple, but standard test methods focus on a single joint.
989
[Page extract]
Insertion and withdrawal
Insertion and withdrawal testing involves applying and measuring the compressive force to an object to push it into a recepticle, then measuring the tension force to pull it out. This may be done for a single cycle or over multiple cycles.
990
[Page extract]
single lap shear
Lap shear testing is used where an adhesive bond joins flat surfaces. The required surfaces may be profiled, single, double or multiple, but standard test methods focus on a single joint.
991
[Page extract]
Compressive shear
Compressive shear testing is simply the pushing apart of a material specimen by applying compressive force from opposite sides in a parallel plane. In this way, the material is stressed in a sliding motion.
992
[Page extract]
Friction
'Dry' friction (as opposed to 'fluid' or 'lubricated' friction) is the force resisting lateral motion between two solid surfaces in contact.
It divides into:
993
[Page extract]
Closure torque
Closures and caps must be applied tight enough to maintain a seal and to resist working loose, but they must not be applied so tightly that the end user cannot reasonably remove them.
994
[Page extract]
Paper & Board
Paper and board are used in a wide range of applications and, as such, they undergo various stages of processing which place significant demands on their material strength.
995
Case study
Porta-garrafas de papelão para bebidas desdobrando
Exemplo de engenharia customizada Um fabricante de caixas totalmente fechadas queria testar a qualidade da força de desdobramento para uma variedade de seus designs, usados principalmente para embalar garrafas e latas de bebidas.
996
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
998
[Page extract]
BS EN ISO 11857
Textile floor coverings, Floor coverings, Sheet flooring, Mechanical testing, Textile testing, Textiles, Tensile testing, Test equipment, Test specimens, Testing conditions.
999
[Page extract]
She adds that the Mecmesin testers lend themselves to the learning environment within which they function.
1000
Case study
Torque operacional do instrumento cirúrgico laparoscópico
Exemplo de engenharia customizada Os instrumentos cirúrgicos endoscópicos e laparoscópicos são operados por ajustes axiais e rotativos no cabo, para realizar movimentos precisos na cabeça.