Mecmesin | Search results

851

^{[Page extract]}

Bar snacks The countline snack bar has diversified into several sectors from pure treat to healthy nutrition. The desired texture is also as diverse - from hard and crunchy to soft and chewy.

852

^{[Page extract]}

ASTM D6117-18

ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:

853

^{[Page extract]}

ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com

854

^{[Page extract]}

BS ISO 6133

BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.

855

^{[Page extract]}

BS EN ISO 10618

Carbon fibres, Mechanical properties of materials, Tensile strength, Tensile testing, Plastics, Impregnated materials, Yarn, Modulus of elasticity, Strain, Tensile strain, Loading, Reinforcing materials, Composite materials, Test equipment, Test specime

856

^{[Page extract]}

SAE AMSSTD

This standard covers the general requirements and methods for testing sandwich core materials and for testing sandwich construction of the types used primarily in aircraft structures.

857

^{[Page extract]}

*corp Mastercard CQM: ID-1

Mastercard CQM requirement covers Peel Strength Test (TM-412 #8120#) and Advanced Peel Strength Test (TN-424 #8240#). Methods are based around ISO 10373-1 to determine the peel strength between 2 layers of an ID or security card.

858

^{[Page extract]}

BS 4863

Gives safety requirements for playpens for use by children up to 15kg in weight. It covers both rigid sided and mesh sided playpens.

859

^{[Page extract]}

ISO 2409

Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.

860

Event

Rice Texture Analysis

Rice is a staple food for billions of people worldwide, and its quality is intrinsically linked to its texture.

861

^{[Page extract]}

ASTM D3577

1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.

862

^{[Page extract]}

BS EN 2243-1

Air transport engineering, Adhesives, Metals, Lapped joints, Adhesion tests, Shear testing, Mechanical testing, Test specimens

863

^{[Page extract]}

BS EN 2243-4

Air transport engineering, Adhesives, Metals, Aluminium alloys, Cellular materials, Tensile testing, Adhesion tests, Test specimens, Specimen preparation, Testing conditions

864

^{[Page extract]}

ASTM D2095

This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.

865

^{[Page extract]}

BS EN ISO 9626

This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.

866

^{[Page extract]}

ASTM D4255 / D4255M-15a

ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.

867

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

868

^{[Page extract]}

ASTM D5868-01

Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which

869

^{[Page extract]}

IEC 61730-2

The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.

870

^{[Page extract]}

BS EN 1707

Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,

871

Case study

바늘 대 페룰 풀 아웃 테스트

요구 사항 고객 인 Oxford Instruments는 두 부품을 분리하기위한 최대 장력을 평가하기 위해 파괴적인 풀 아웃 테스트를 수행하기를 원했습니다. 이 시스템은 피하 주사 바늘 끝에있는 주름진 페룰의 인장 무결성을 확인하도록 설계되었습니다.

872

^{[Page extract]}

ASTM D4179

1.1 This test method covers determining the resistance of formed catalysts and catalyst carriers to compressive force and is applicable to regular catalyst shapes such as tablets and spheres.

873

^{[Page extract]}

ASTM D1578

Significance and Use Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.

874

^{[Page extract]}

ASTM D695-15

ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.

875

^{[Page extract]}

BS 6965-1

Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard