Mecmesin | Search results

1601

^{[Page extract]}

BS EN 14350-1

Resusable teats and drinking accessories Resusable feeding bottles and drinking cups Single use feeding bottles, feeding teats, feeding bags and drinking accessories, which do not contain fluid when purchased.

1602

^{[Page extract]}

TAPPI T 456

TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.

1603

^{[Page extract]}

BS EN ISO 6259-1

BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.

1604

^{[Page extract]}

*corp 01M-01-216

To determine the maximum force required to rupture (break) a woven fabric – Rugby only

1605

^{[Page extract]}

ASTM C907

This test method covers a laboratory procedure for determining the tensile adhesive strength of a preformed tape sealant. The type of failure can be determined, and the degree of cohesive/adhesive failure can be estimated.

1606

^{[Page extract]}

ASTM D6713-14

Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro

1607

^{[Page extract]}

CETIE Guide 3

This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.

1608

^{[Page extract]}

ASTM C364

This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.

1609

^{[Page extract]}

ASTM D4476 / D4476M-14

ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.

1610

^{[Page extract]}

MIL AS23190A

AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment

1611

^{[Page extract]}

ASTM D2918

This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper

1612

^{[Page extract]}

NF S86-604

This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.

1613

^{[Page extract]}

BS EN 5350-C5

Adhesives, Test methods, Adhesive strength, Longitudinal, Strength of materials, Shear strength, Dimensional tolerances

1614

^{[Page extract]}

ASTM C598

This test method covers the determination of the annealing point and the strain point of a glass by measuring the rate of midpoint viscous bending of a simply loaded glass beam.

1615

^{[Page extract]}

BS EN ISO 527-2

ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.

1616

^{[Page extract]}

ASTM C1161

This test method covers the determination of flexural strength of advanced ceramic materials at ambient temperature. Four-point and three-point loadings with prescribed spans are the standard.

1617

^{[Page extract]}

ASTM D5467 / D5467M-97

ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.

1618

Event

Webinar: Rice Texture Analyzer (Thai) - เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว

เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว หนึ่งในปัจจัยที่สําคัญที่สุด ซึ่งมีผลต่อความสำเร็จของผลิตภัณฑ์ข้าวคือ เนื้อสัมผัส เนื้อสัมผัสของข้าวส่งผลโดยตรงต่อความพึงพอใจของผู้บริโภค และความน่าเชื่อถือของผู้ผลิตข้าว นั่นคือเหตุผลว่า

1619

^{[Page extract]}

ASTM D3968

This test method covers the measurement of rotational torques of Type IIIA child-resistant closures as a means of monitoring normal functioning of the child-resistant package.

1620

^{[Page extract]}

Tack test

1621

^{[Page extract]}

ASTM F806-99a

ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.

1622

^{[Page extract]}

IPC TM-650

A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature

1623

^{[Page extract]}

ISO 21180

ISO 21180 specifies a test method for the determination of the maximum tensile strength of light conveyor belts.

1624

^{[Page extract]}

ASTM D1710

Among tests for electrical and dimensional (temperature) stability, includes methods for tensile characteristics.

1625

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.