Mecmesin | Search results

876

^{[Page extract]}

BS ISO 6133

BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.

877

^{[Page extract]}

ISO 2409

Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.

878

^{[Page extract]}

ASTM D6117-18

ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:

879

Case study

Pump dispenser bottle operation

Customised engineering example As a method to dispense liquids and sprays propellants, such as pressurised gas, are avoided for many reasons. Dispensers with manual spring-loaded pumps are often used in their place.

880

^{[Page extract]}

BS EN 2243-4

Air transport engineering, Adhesives, Metals, Aluminium alloys, Cellular materials, Tensile testing, Adhesion tests, Test specimens, Specimen preparation, Testing conditions

881

^{[Page extract]}

ASTM D3577

1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.

882

^{[Page extract]}

BS EN ISO 9626

This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.

883

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

884

^{[Page extract]}

ASTM D2095

This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.

885

^{[Page extract]}

BS EN 2243-1

Air transport engineering, Adhesives, Metals, Lapped joints, Adhesion tests, Shear testing, Mechanical testing, Test specimens

886

^{[Page extract]}

ASTM D4179

1.1 This test method covers determining the resistance of formed catalysts and catalyst carriers to compressive force and is applicable to regular catalyst shapes such as tablets and spheres.

887

^{[Page extract]}

IEC 61730-2

The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.

888

^{[Page extract]}

ASTM D4255 / D4255M-15a

ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.

889

^{[Page extract]}

ASTM D1578

Significance and Use Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.

890

^{[Page extract]}

BS EN 1707

Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,

891

Page

You have been subscribed to the Mecmesin newsletter

Thank you

We hope you enjoy the regular updates on our developments in force, materials and torque testing.

892

^{[Page extract]}

Customised testing equipment and fixtures

Mecmesin testing systems are highly versatile and we specialise in conquering force and torque testing challenges of all sizes.

893

^{[Page extract]}

ISO 12625-5

ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.

894

^{[Page extract]}

ASTM D5868-01

Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which

895

^{[Page extract]}

BS EN 61238-1

Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T

896

^{[Page extract]}

ASTM D695-15

ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.

897

^{[Page extract]}

ASTM D882-18

ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile strength,

898

Case study

Luer lock fastening and release torque

Customised engineering example Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.

899

^{[Page extract]}

BS 6965-1

Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard

900

Case study

Smoke grenade canister integrity

Customised engineering example A manufacturer of smoke grenades required a means of testing the cap pull-off strength. The particular challenge was to grip the smooth metal cylinder for up to 5 kN of pulling force.