Mecmesin | Search results

1426

^{[Page extract]}

Wine & Spirits Capping: Cork Pull & Twist Caps

Wine packaging has a great influence on the quality of the product delivered to the customer.

1428

^{[Page extract]}

This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill

1429

^{[Page extract]}

ASTM D5450/D5450M-11

This test method determines the transverse tensile properties of wound polymer matrix composites reinforced by high-modulus continuous fibers.

1430

^{[Page extract]}

ASTM D5448-11

This test method determines the inplane shear properties of wound polymer matrix composites reinforced by high-modulus continuous fibers. It describes testing of hoop wound (90°) cylinders in torsion for determination of inplane shear properties.

1431

^{[Page extract]}

BS EN 12655

Gymnastics equipment, Sports equipment, Safety measures, Equipment safety, Classification systems, Dimensions, Height, Strength of materials, Stability, Mechanical testing, Vertical, Horizontal, Performance testing, Instructions for use

1432

^{[Page extract]}

ASTM D1000

These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows: Class 1—Non-elastomeric backings made from materials

1433

^{[Page extract]}

ISO 11608-5

This part of ISO 11608 specifies requirements and test methods for the automated functions of needle-based injection systems with automated functions (NIS-AUTO), for the administration of medicinal products in humans.

1434

^{[Page extract]}

BS EN 565

Mountaineering equipment, Outdoor sports equipment, Sports equipment, Safety measures, Equipment safety, Tape, Webbing, Tensile strength, Stability, Weight measurement, Marking, Test specimens, Testing conditions

1435

^{[Page extract]}

ASTM D622-99

ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<

1436

^{[Page extract]}

ASTM D926-17

ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.

1437

^{[Page extract]}

Streamline your testing process with Mecmesin automation solutions

1438

^{[Page extract]}

ASTM D3658

This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.

1439

^{[Page extract]}

BS EN 12242

The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g

1440

^{[Page extract]}

ASTM D3106

This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.

1441

^{[Page extract]}

ISO 13935-1

ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.

1442

^{[Page extract]}

ASTM D2633

ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.

1443

^{[Page extract]}

ISO 17454

ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.

1444

^{[Page extract]}

BS EN 2597

BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics. Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.

1445

^{[Page extract]}

ISO 6922

Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.

1446

^{[Page extract]}

FEFCO 4-6,8,11,50,55

Older standards and international replacements used for:

1447

^{[Page extract]}

ASTM C297

This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.

1448

^{[Page extract]}

BS EN 14477

Packaging, Packaging materials, Flexible materials, Perforating tests, Mechanical testing

1449

^{[Page extract]}

ASTM C961

This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.

1450

^{[Page extract]}

ASTM D5587-08

This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.