Mecmesin | Search results

1576

^{[Page extract]}

FINAT FTM1

This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.

1577

^{[Page extract]}

ASTM D3914

ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.

1578

^{[Page extract]}

BS EN ISO 376

BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.

1579

^{[Page extract]}

During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.

1580

^{[Page extract]}

ASTM D1995

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1581

^{[Page extract]}

ISO 7810

Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.

1582

^{[Page extract]}

ASTM D7137 / D7137M-17

ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation

1583

^{[Page extract]}

SAE J174

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.

1584

^{[Page extract]}

ASTM D5766 / D5766-M

ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.

1585

^{[Page extract]}

ASTM B913

This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.

1586

^{[Page extract]}

BS EN 1465

Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.

1587

^{[Page extract]}

ASTM D1871

This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.

1588

^{[Page extract]}

ASTM D380

ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.

1589

^{[Page extract]}

ISO 8510-1

Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.

1590

^{[Page extract]}

BS EN 1393

BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.

1591

^{[Page extract]}

BS EN ISO 8670-2

Two part test on filled bags: 1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate

1592

^{[Page extract]}

ASTM D2659

ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.

1593

^{[Page extract]}

ISO 594-2

ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.

1594

^{[Page extract]}

PSTC 8

Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape. The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.

1595

^{[Page extract]}

FINAT FTM2

This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.

1596

^{[Page extract]}

BS EN ISO 11608-3

Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions

1597

^{[Page extract]}

ASTM D3410 / D3410M

ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.

1598

^{[Page extract]}

BS EN 12316-1

Waterproof materials, Sheet materials, Flexible materials, Peel resistance, Peeling tests, Joints, Bitumens, Bituminous products, Roof coverings, Test equipment, Specimen preparation

1599

^{[Page extract]}

BS EN 12346

Gymnastics equipment, Wall bars, Ladders, Sports equipment, Indoor sports equipment, Design, Dimensions, Height, Dimensional tolerances, Shape, Strength of materials, Safety measures, Marking, Instructions for use, Equipment safety, Mechanical testing,

1600

Case study

Coppia di serraggio dei distributori della pompa

Requisiti Pfeiffer (ora Aptar Pharma), con sede in Germania, è un produttore leader di atomizzatori e sistemi di dosaggio per l'industria farmaceutica e cosmetica.