Search results
1101
[Page extract]
ASTM D4255 / D4255M-15a
ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.
1102
[Page extract]
IEC 61730-2
The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.
1103
Case study
Essais d'arrachage sur brosses et pinceaux cosmétiques
Exemple d'ingénierie sur mesure
Notre client est une grande entreprise de cosmétiques qui utilise une variété de brosses de pinceaux pour toutes les applications et qui souhaite tester l’intégrité des poils en traction.
1104
Case study
Serrage Luer lock et couple de déverrouillage
Exemple d'ingénierie sur mesure
Les normes de test Luer Lock exigent fréquemment la mesure du couple tout en appliquant simultanément une force axiale prédéfinie.
1105
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
1106
Case study
Essais sur neutralisation de la sécurité de portes de train
Exemple d'ingénierie sur mesure
Un opérateur ferroviaire britannique avait besoin d’une méthode permettant de vérifier leurs portes coulissantes de wagon et la sensibilité à la détection d’un obstacle lors de la fermet
1107
[Page extract]
BS EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
1108
[Page extract]
BS EN 61067-2
Glass fibres, Polyesters, Woven fabrics, Tape, Tape yarns, Filament (textile fibre), Polyester fibres, Textile glass, Dimensional changes, Shrinkage tests, Tensile strength, Test specimens, Testing conditions, Test equipment
1109
[Page extract]
ASTM F152-95
ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.
1110
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1111
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile strength,
1112
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
1113
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
1114
Case study
Essai de rigidité du film isolant
Exemple d'ingénierie sur mesure Familier avec la flexion en trois points pour tester les propriétés de résistance à la flexion?
1115
Case study
Force de fonctionnement de distributeur à pompe
Exemple d'ingénierie sur mesure
En tant que méthode de distribution de liquides et de pulvérisations, les propulseurs à spray, utilisant du gaz sous pression, sont évités pour de nombreuses raisons.
1116
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1117
Case study
Pump dispenser bottle operation
Customised engineering example
As a method to dispense liquids and sprays propellants, such as pressurised gas, are avoided for many reasons. Dispensers with manual spring-loaded pumps are often used in their place.
1118
Case study
Essai du ressort de torsion
Exemple d'ingénierie sur mesure
Contrairement à la plupart des ressorts de compression et de traction, les ressorts de torsion se présentent sous différentes formes avec différentes positions des branches.
1119
[Page extract]
BS EN 1263-1
Safety nets, Restraint systems (protective), Construction equipment, Safety devices, Building sites, Occupational safety, Performance, Man-made fibres, Polyamide fibres, Polyolefin fibres, Ropes, Performance testing, Mechanical testing, Tensile testing,
1120
[Page extract]
EN 22872
EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.
1121
[Page extract]
BS 6965-1
Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard
1122
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1123
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
1125
[Page extract]
BS EN 14372
This document establishes minimum safety requirements and specifies appropriate test methods for children’s cutlery and feeding utensils designed for the use of children aged up to 3 years, with or without parental supervision.