Mecmesin | Search results

926

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

927

^{[Page extract]}

This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.

928

^{[Page extract]}

ASTM D1578

Significance and Use Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.

929

^{[Page extract]}

BS EN 1707

Syringes, Conical fittings (syringes), Injection instruments, Locking and locating devices, Fitting, Pipe fittings, Medical equipment, Medical instruments, Blood transfusion equipment, Dimensions, Dimensional tolerances, Performance testing, Leak tests,

930

^{[Page extract]}

ASTM D4179

1.1 This test method covers determining the resistance of formed catalysts and catalyst carriers to compressive force and is applicable to regular catalyst shapes such as tablets and spheres.

931

^{[Page extract]}

ASTM D4255 / D4255M-15a

ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.

932

^{[Page extract]}

IEC 61730-2

The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.

933

^{[Page extract]}

ASTM D5868-01

Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which

934

Caso de estudio

Electrical connector insertion and withdrawal forces

Customised engineering example Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.

935

^{[Page extract]}

BS 6965-1

Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard

936

^{[Page extract]}

BS EN 61238-1

Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T

937

^{[Page extract]}

Customised testing equipment and fixtures

Mecmesin testing systems are highly versatile and we specialise in conquering force and torque testing challenges of all sizes.

938

^{[Page extract]}

BS EN 61067-2

Glass fibres, Polyesters, Woven fabrics, Tape, Tape yarns, Filament (textile fibre), Polyester fibres, Textile glass, Dimensional changes, Shrinkage tests, Tensile strength, Test specimens, Testing conditions, Test equipment

939

^{[Page extract]}

ASTM F152-95

ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.

940

Página

You have been subscribed to the Mecmesin newsletter

Thank you

We hope you enjoy the regular updates on our developments in force, materials and torque testing.

941

Caso de estudio

Smoke grenade canister integrity

Customised engineering example A manufacturer of smoke grenades required a means of testing the cap pull-off strength. The particular challenge was to grip the smooth metal cylinder for up to 5 kN of pulling force.

942

^{[Page extract]}

ISO 12625-5

ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.

943

^{[Page extract]}

ASTM D882-18

ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile strength,

944

^{[Page extract]}

ASTM D695-15

ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.

945

Caso de estudio

Luer lock fastening and release torque

Customised engineering example Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.

946

^{[Page extract]}

ISO 6475

ISO 6

947

^{[Page extract]}

SAE USCAR-21-4

This specification defines test methods and requirements for validation of solderless crimped connections.

948

^{[Page extract]}

BS EN 1263-1

Safety nets, Restraint systems (protective), Construction equipment, Safety devices, Building sites, Occupational safety, Performance, Man-made fibres, Polyamide fibres, Polyolefin fibres, Ropes, Performance testing, Mechanical testing, Tensile testing,

949

^{[Page extract]}

EN 22872

EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.

950

^{[Page extract]}

ASTM C1147

ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.