Search results
1351
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1352
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
1353
[Page extract]
ASTM D5587-08
This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.
1354
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
1355
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
1356
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.
1357
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
1358
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
1359
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1360
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
1361
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
1362
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1363
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
1364
Caso de estudio
Prueba de primavera estabilizada
Ejemplo de ingeniería personalizada Nuestro cliente necesitaba probar una serie de muelles pequeños y livianos bajo compresión. Para evitar el pandeo y el movimiento lateral de los resortes, se requería un eje de soporte o una varilla guía.
1365
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
1367
[Page extract]
ASTM D3163
ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.
1368
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1369
[Page extract]
BS EN 1492-1
Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web
1370
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
1371
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
1372
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
1373
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1374
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.
1375
[Page extract]
BS EN 50289-3-2
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Elongation, Electric conductors