Mecmesin | Search results

1701

^{[Page extract]}

ISO 7810

Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.

1702

^{[Page extract]}

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1703

^{[Page extract]}

ASTM D5656-10

This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.

1704

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1705

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1706

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1707

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1708

^{[Page extract]}

SAE J174

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 1/4 through 1 in nomial diameters.

1709

^{[Page extract]}

ASTM D5766 / D5766-M

ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.

1710

^{[Page extract]}

ASTM B913

This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.

1711

^{[Page extract]}

BS EN 1465

Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.

1712

^{[Page extract]}

ASTM D7137 / D7137M-17

ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation

1713

^{[Page extract]}

ASTM D1871

This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.

1714

^{[Page extract]}

ASTM D380

ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.

1715

^{[Page extract]}

ISO 8510-1

Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.

1716

^{[Page extract]}

BS EN 1393

BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.

1717

^{[Page extract]}

BS EN ISO 8670-2

Two part test on filled bags: 1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate

1718

^{[Page extract]}

ASTM D2659

ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.

1719

^{[Page extract]}

ISO 594-2

ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.

1720

^{[Page extract]}

PSTC 8

Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape. The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.

1721

^{[Page extract]}

FINAT FTM2

This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.

1722

^{[Page extract]}

ASTM D816-06

These test methods cover tests to measure the properties of adhesives, commonly called rubber cements, that may be applied in plastic or fluid form and that are manufactured from natural rubber, reclaimed rubber, synthetic elastomers, or combinations of

1723

^{[Page extract]}

BS EN ISO 11608-3

Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions

1724

^{[Page extract]}

ASTM D3410 / D3410M

ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.

1725

^{[Page extract]}

BS EN 12316-1

Waterproof materials, Sheet materials, Flexible materials, Peel resistance, Peeling tests, Joints, Bitumens, Bituminous products, Roof coverings, Test equipment, Specimen preparation