Search results
1751
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
1752
[Page extract]
ASTM F1044-05
This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures.
1753
Case study
Einstellbare Drehmomentprüfung der Brille
Beispiel für kundenspezifisches Engineering Adlens stellt adaptive Brillengläser her, bei denen die optische Leistung durch ein seitliches Einstellrad eingestellt wird, das dann entfernt wird.
1755
Case study
Prüfung der Isolierfilmsteifigkeit
Beispiel für kundenspezifisches Engineering Mit dem Dreipunktbiegen zum Testen der Biegefestigkeit vertraut?
1756
Case study
Bulk Liquid Carrier Verschlüsse
Beispiel für kundenspezifisches Engineering Unser Kunde stellt flüssige Massengutfrachter her, die mit zweiteiligen Ventilverschlüssen aus Kunststoff ausgestattet sind.
1757
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
1758
[Page extract]
BS EN 565
Mountaineering equipment, Outdoor sports equipment, Sports equipment, Safety measures, Equipment safety, Tape, Webbing, Tensile strength, Stability, Weight measurement, Marking, Test specimens, Testing conditions
1759
[Page extract]
ASTM D622-99
ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<
1760
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
1761
[Page extract]
BS EN 12242
The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g
1762
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
1763
[Page extract]
ASTM D5587-08
This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.
1764
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
1765
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
1766
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
1767
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
1768
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1769
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
1770
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1771
[Page extract]
VectorPro test definition
https://ahpublic.s3.eu-west-2.amazonaws.com/VectorPro/vcs/export/live/v…
1772
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
1773
[Page extract]
ASTM D3163
ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.
1774
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.