Search results
1451
[Page extract]
ASTM D7249-12
This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the
1452
Article/Campaign
Test title
Tensile Testing Solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
1453
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
1454
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
1455
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
1456
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
1457
[Page extract]
ISO 8009
ISO 8009:2004 specifies the minimum requirements and test methods to be used for reusable diaphragms made from natural rubber and silicone rubber. These diaphragms are intended for contraceptive use.
1458
Specials
Vector instruments - Intuitive touchscreens
Intuitive touchscreen
The most advanced touchscreen force and torque gauges, powered by Vector OS.
Handheld instruments built for tough environments to deliver accuracy and reliability.
1459
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
1460
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
1461
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
1462
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
1463
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
1464
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1465
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
1466
[Page extract]
ASTM C403/C403M
This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
1467
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
1468
[Page extract]
BS EN 455-2
Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing
1469
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
1470
[Page extract]
ASTM D3480
These test methods cover the measurement of the downward force required to open or activate child-resistant snap-engagement packages.
1471
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
1472
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
1473
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1474
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1475
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.