Search results
876
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
877
[Page extract]
Texture testing
Terms commonly used across different food sectors to describe food attributes include hardness, tenderness, firmness, cohesiveness, springiness, stickiness etc.
878
[Page extract]
Fastening torque
Bolts and screws secure many constructions, and the equal integrity and performance of each is crucial.
879
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
880
[Page extract]
Shear
Shear testing is a very popular and valuable test method applicable to food texture analysis.
This method applies slicing or 'shearing' to the product, which replicates the action of the front incisors when food is introduced into the mouth.
881
[Page extract]
texture, compression
Compression is one of the most common texture tests, especially for food products. Typically a sample is placed on a flat surface and an upper compression platen is lowered into the sample.
882
[Page extract]
T-peel
T-peel test procedures are commonly used to measure peel strength for flexible laminates.In this test, the entire load applied is transmitted to the bond. This type of peel thus tends to provide the lowest values of any peel test
883
[Page extract]
Compressive burst
The integrity of a fluid or gas-filled container can be tested in terms of its propensity to burst.
This may involve a failure in the material by splitting, or perhaps a seal/seam gives way or even the closure can break loose.
884
[Page extract]
puncture resistance
Puncture resistance is a function of controlled stretch and tear at a point.
885
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
886
Article/Campaign
Mecmesin pioneers the world’s ultimate digital force gauge
Ground-breaking VFG touchscreen force gauge
887
Case study
Ứng dụng và lực tháo nắp phân phối thùng chứa chất lỏng công nghiệp
Yêu cầu Cần có một hệ thống để đo lực đẩy và lực tháo của nắp đúc phun từ một thiết kế mới của can dầu.
888
Case study
Ống sốc kíp nổ
Yêu cầu Một nhà sản xuất ống kíp nổ không giật điện cho các ứng dụng công nghiệp đã có yêu cầu kiểm tra độ bền kéo chuyên dụng.
889
Accessory
QC Type C Adapter, 20 mm M, c/w pin and M6 fixing screws
432-284
QC Male Post 20mm c/w cross-pin, locking collar…
890
Accessory
1/2" upper chuck assembly for use on Helixa sensors (3 N.m & 6 N.m only)
432-617
A standard self-centering 3-jaw chuck with key.
It has a maximum ½" (12.7 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
891
Accessory
Adapter, 5 kN, 5-16 UNC to M6, F to F
432-330
Female-to-female Adapter
Allows a grip to be connected to a force gauge/loadcell or test stand where thread connections are different.
892
Accessory
Compression Plate, Hardened and Ground, 70 mm, 5-16 UNC
432-338
Hardened and ground compression plates have a smooth, scratch-proof surface ideal for compression testing on samples that could damage a standard compression plate, such as springs.
70mm diameter having 5-16 UNC female thread.
893
Accessory
Self-levelling Compression Plate Steel - 116 mm, 25 kN, QC-20 fitting
MecS223k-116
MecS223k - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates.. ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
894
Accessory
Compression Plate, Self-levelling, Hardened & Ground, 175 mm, 5-16 UNC
432-352
Self-levelling compression plates are ideal for general compression testing on a range of materials and finished products. Self-levelling allows parallelism to be set for those applications where it is critical to accurately measure the deformation of a…
895
Accessory
Clevis Grip (small), 500 N, 10-32 UNF
432-403
Small Clevis Grip fitted with female 10-32 UNF thread and supplied with male grub-screw.
Used for securing odd-shaped parts for testing tensile forces below 500N.
896
Accessory
Dovetail Bracket for AFG or BFG
432-427
The dovetail bracket is used for mounting the Advanced Force Gauge (AFG) and Basic Force Gauge (BFG) to test stands. It allows the operator to precisely align the gauge on the stand. Supplied with fixing screws.
Note: maximum load 2500 N
897
Accessory
Self-levelling Compression Plate Steel - 116 mm, 50 kN, QC-32 fitting
MecS223g-116
MecS223g - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates - ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…
898
Accessory
Inverted Chisel Point, Ø 12 mm, 5 kN, 5-16 UNC
432-357
For compression testing of cylindrical or wire specimens up to 5 kN.
Specimen is located centrally within the inverted V-shape and compressed to a set distance or a break.
Fitted with a 5-16 UNC female thread for connection to loadcell
899
Accessory
Dial Gauge Bracket Set
432-167
The dial gauge bracket set allows an analogue or digital comparator to be securely fitted to the MDD manual test stand. Digital comparators are suitable for measuring crosshead movement over short distances.
900
Accessory
Lightweight Vice Grip - Double Action, 250 N, Opening 0-46mm, 10-32 UNF
Mec227-S46
MEC 227-S46 (body only):
A Lightweight Vice Grip providing free adjustment of both jaws, allowing them to be aligned around the central axis to accommodate tensile testing of both symmetrical and asymmetrical specimens.
Rated to 250 N in tension with…