Search results
676
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
677
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
678
[Page extract]
ISO 5628
Specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
679
[Page extract]
ASTM D5602/D5602M-18
An important factor affecting the performance of many membrane roofing systems is their ability to resist static puncture loads. This test method provides a means for assessing static puncture resistance.
680
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
681
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
682
Case study
Tính toàn vẹn của bao bì các tông dán
Yêu cầu Graphic Packaging International là nhà thiết kế và sản xuất bao bì thực phẩm và đồ uống hàng đầu.
683
Case study
Kiểm tra độ bền kéo của vải nội thất
Yêu cầu Được sự hỗ trợ của Hộ gia đình Hoàng gia của Lâu đài Windsor, một sinh viên Đại học Buckinghamshire New University đang nghiên cứu tính chất hao mòn và độ bền của vải dệt từ sợi đay truyền thống của Anh, được sử dụng trong việc chế tạo
684
Sensor
Cảm biến - MultiTest-dV
Cảm biến lực MultiTest-dV là một trình thử nghiệm có tính linh hoạt cao, có thể được định cấu hình bằng Máy đo lực nâng cao để thử nghiệm sản phẩm hoặc Cảm biến tải nâng cao để thử nghiệm vật liệu cơ bản. AFG Một máy đo lực kỹ thuật số với các tính năng…
685
[Page extract]
Compressive shear
Compressive shear testing is simply the pushing apart of a material specimen by applying compressive force from opposite sides in a parallel plane. In this way, the material is stressed in a sliding motion.
686
[Page extract]
Friction
'Dry' friction (as opposed to 'fluid' or 'lubricated' friction) is the force resisting lateral motion between two solid surfaces in contact.
It divides into:
687
[Page extract]
Flexure
Flexural or bend testing is used It is a way of determining how something will react when it is put under opposing forces across a span.to evaluate both the ductility and soundness of a material.
688
[Page extract]
double lap shear
Lap shear testing is used where an adhesive bond joins flat surfaces.
The required surfaces may be profiled, single, double or multiple, but standard test methods focus on a single joint.
689
[Page extract]
Insertion and withdrawal
Insertion and withdrawal testing involves applying and measuring the compressive force to an object to push it into a recepticle, then measuring the tension force to pull it out. This may be done for a single cycle or over multiple cycles.
690
[Page extract]
single lap shear
Lap shear testing is used where an adhesive bond joins flat surfaces. The required surfaces may be profiled, single, double or multiple, but standard test methods focus on a single joint.
691
[Page extract]
Closure torque
Closures and caps must be applied tight enough to maintain a seal and to resist working loose, but they must not be applied so tightly that the end user cannot reasonably remove them.
692
[Page extract]
Paper & Board
Paper and board are used in a wide range of applications and, as such, they undergo various stages of processing which place significant demands on their material strength.
693
Sensor
Cảm biến - Người kiểm tra vật liệu
Cảm biến Hệ thống kiểm tra vật liệu OmniTest và MultiTest-dV sử dụng nhiều loại Cảm biến tải nâng cao có độ chính xác cao (ELS) của Mecmesin để ghi lại tải trọng kéo và nén. ELS Cảm biến lực chính xác kết nối trực tiếp với chân đế OmniTest hoặc MultiTest-…
694
[Page extract]
BS EN 28510-1
Test for measuring resistance to peeling at a nominal 90°, particularly suitable for adherends that are insufficiently flexible for a 180° peel test.
695
[Page extract]
Springs
Springs are elastic objects used to store mechanical energy and they change shape in response to external forces, returning to their original shapes when the forces are removed.
696
Case study
Bulk liquid carrier closures
Customised engineering example
Our client manufactures liquid bulk carriers fitted with two-part plastic valve closures. The collar is welded to a plastic bag, and the valve closure is fixed onto it by a compression joint.
698
Case study
Kiểm tra độ bền kéo trên miếng đệm cao su
Yêu cầu British Gaskets là nhà sản xuất chính về gioăng, sản phẩm làm kín và khuôn. Chúng được làm từ nhiều loại vật liệu khác nhau để phù hợp với nhiều ứng dụng.
699
[Page extract]
BS EN 863
Protective clothing, Clothing, Perforating tests, Penetration tests, Mechanical testing, Tensile testing, Test equipment, Specimen preparation, Performance testing
700
Case study
Syringe plunger breakaway and glide force
Customised engineering example
The majority of syringes are single-use, disposable and manually-operated.