Search results
901
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
902
[Page extract]
EN 22872
EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.
903
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
905
[Page extract]
BS EN 1263-1
Safety nets, Restraint systems (protective), Construction equipment, Safety devices, Building sites, Occupational safety, Performance, Man-made fibres, Polyamide fibres, Polyolefin fibres, Ropes, Performance testing, Mechanical testing, Tensile testing,
906
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile strength,
907
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
910
[Page extract]
Needle penetration and drag testing assess the force required to insert a needle into a material and the friction experienced during this process. This test ensures that syringes perform reliably, reducing risks to patients and healthcare providers.
911
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
912
[Page extract]
Compression testing
Compression testing is a way of determining how something will react when it is squashed, or when a force is applied to it in compression.
It is performed to:
913
[Page extract]
Texture testing
Terms commonly used across different food sectors to describe food attributes include hardness, tenderness, firmness, cohesiveness, springiness, stickiness etc.
914
[Page extract]
Fastening torque
Bolts and screws secure many constructions, and the equal integrity and performance of each is crucial.
915
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
916
[Page extract]
Shear
Shear testing is a very popular and valuable test method applicable to food texture analysis.
This method applies slicing or 'shearing' to the product, which replicates the action of the front incisors when food is introduced into the mouth.
917
[Page extract]
texture, compression
Compression is one of the most common texture tests, especially for food products. Typically a sample is placed on a flat surface and an upper compression platen is lowered into the sample.
918
[Page extract]
T-peel
T-peel test procedures are commonly used to measure peel strength for flexible laminates.In this test, the entire load applied is transmitted to the bond. This type of peel thus tends to provide the lowest values of any peel test
919
[Page extract]
Compressive burst
The integrity of a fluid or gas-filled container can be tested in terms of its propensity to burst.
This may involve a failure in the material by splitting, or perhaps a seal/seam gives way or even the closure can break loose.
920
[Page extract]
puncture resistance
Puncture resistance is a function of controlled stretch and tear at a point.
921
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
922
Article/Campaign
Mecmesin pioneers the world’s ultimate digital force gauge
Ground-breaking VFG touchscreen force gauge
923
Accessory
Inverted Chisel Point, Ø 12 mm, 5 kN, 5-16 UNC
432-357
For compression testing of cylindrical or wire specimens up to 5 kN.
Specimen is located centrally within the inverted V-shape and compressed to a set distance or a break.
Fitted with a 5-16 UNC female thread for connection to loadcell
924
Accessory
Pin Chuck, 100 N, 10-32 UNF
432-382
Pin chucks are specifically designed for gripping circular or rod-type specimens of diameters between 0.5 - 3.5mm.
For tension and compression testing below 100N.
Fitted with adaptor having 10-32 UNF female threaded hole & 10-32 UNF grub-screw
925
Accessory
Spring-loaded Pinch Grip with Chain Link, 20 N, QC-20 fitting
MecS205k
A Spring-loaded Pinch Grip designed for small-area contact (10mm x 10mm) to grip a delicate sample.
The sprung-loaded adjustable screw-mechanism allows an opening up to 3.4mm and acts in a pincer motion to secure specimens.
Fitted with a flexible chain…