Mecmesin | Search results

1601

^{[Page extract]}

TAPPI T 576

This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.

1602

^{[Page extract]}

ISO 188

ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:

1603

^{[Page extract]}

Tension

There are in essence two types of tensile grips:

1604

^{[Page extract]}

*corp 01M-01-309

To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.

1605

^{[Page extract]}

BS EN 455-2

Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing

1606

^{[Page extract]}

ASTM C1341

This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.

1607

^{[Page extract]}

BS EN ISO 6892-1

This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.

1608

^{[Page extract]}

USP <381>

This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.

1609

^{[Page extract]}

ASTM D4475-02

ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.

1610

^{[Page extract]}

CETIE Guide 4

This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.

1611

^{[Page extract]}

ASTM D413-98

ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.

1612

^{[Page extract]}

BS EN 17394-2

This document defines a test method for security of attachment of functional and decorative buttons to clothing including garments such as gloves, hats, scarves, hosiery, ties, and textile belts. The scope of this document is limited to sewn-on buttons,

1613

^{[Page extract]}

ISO 4049

This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or

1614

Article/Campaign

Test title

Tensile Testing Solutions

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.

1615

^{[Page extract]}

ISO 16047

ISO 16047:2005 specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.

1616

^{[Page extract]}

ISO 9727-4

ISO 9727-4 specifies a test method for determining the percentage of diameter recovery of cylindrical cork stoppers, after compression.

1617

^{[Page extract]}

ASTM D3470

This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)

1618

^{[Page extract]}

ASTM D6324-11

ASTM D6324 covers the minimum requirements for individually packaged male condoms made from polyurethane. This specification also describes the minimum inspection and quality levels that shall be utilized in referee tests.

1619

^{[Page extract]}

ASTM D7249-12

This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the

1620

^{[Page extract]}

ASTM C403/C403M

This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.

1621

^{[Page extract]}

BS EN 2243-2

This standard defines the general requirements for the determination of strength of structural adhesives by testing in peel metal to metal joints, at ambient or other temperatures.

1622

^{[Page extract]}

ISO 13954

ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.

1623

^{[Page extract]}

ASTM E2658-15

These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices

1624

Specials

Vector instruments - Intuitive touchscreens

Intuitive touchscreen The most advanced touchscreen force and torque gauges, powered by Vector OS. Handheld instruments built for tough environments to deliver accuracy and reliability.

1625

^{[Page extract]}

ISO 283

ISO 283 specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass.