Search results
1776
[Page extract]
ASTM D6004-04
This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.
1777
[Page extract]
ASTM F2256-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
1778
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
1779
[Page extract]
ASTM D5458-95
This test method measures cling between two layers of film, in both a stretched and unstretched condition.
1780
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.
1781
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
1782
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
1783
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
1784
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
1785
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
1786
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
1787
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
1788
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
1789
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
1790
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1791
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
1792
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
1793
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
1795
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
1796
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1797
[Page extract]
ISO 3781
Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
1798
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
1799
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
1800
[Page extract]
ISO 9727-2
This part of ISO 9727 specifies a test method for:
⎯ measuring the mass of cylindrical cork stoppers ready for use or semi-worked, totally or partially made of agglomerated cork, and