Mecmesin | Search results

1626

^{[Page extract]}

BS 2782-3: 360C

BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method

1627

^{[Page extract]}

The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.

1628

^{[Page extract]}

ISO 12048

Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.

1629

^{[Page extract]}

BS EN 12814-2

BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.

1630

^{[Page extract]}

Kariyer

Mecmesin, her bireyi ve ihtiyaçlarını önemseyen aile dostu bir şirkettir. 1977 yılında kurulan, biz kuvvet, malzeme ve tork test çözümleri için lider bir mühendislik şirketi vardır.

1631

^{[Page extract]}

BS EN 12467

Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio

1632

^{[Page extract]}

Tüketici ürünleri

Genellikle evde bulunan ürünler için Mecmesin test çözümleri ...

1633

^{[Page extract]}

ISO 8627

Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.

1634

^{[Page extract]}

SAE J 1907

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.

1635

^{[Page extract]}

BS ISO 3597-2

ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.

1636

^{[Page extract]}

FINAT FTM1

This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.

1637

^{[Page extract]}

ASTM D3914

ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.

1638

^{[Page extract]}

BS EN ISO 376

BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.

1639

^{[Page extract]}

ASTM D5656-10

This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.

1640

^{[Page extract]}

ASTM D1995

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1641

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1642

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1643

^{[Page extract]}

ASTM D6195-03

These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.

1644

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1645

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1646

^{[Page extract]}

SAE J174M

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.

1647

^{[Page extract]}

BS EN 1492-1

Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web

1648

^{[Page extract]}

ASTM D7834-13

During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.

1649

^{[Page extract]}

ASTM F607-03

The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.

1650

^{[Page extract]}

BS EN 50289-3-17

Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths