Search results
701
Accessory
Large Chain Link Assembly (long) and Hook, 2.5 kN, 5-16 UNC
432-410
The large chain link assembly (long) and hook are used to attach to a variety of objects, which are otherwise difficult to hold.
The chain is 1 m long and is supplied with a clevis fastener at each end. Into one end is screwed a large test hook, which…
702
Accessory
Small Container Holder, 100 N, 10-78 mm
432-493
A versatile gripping fixture to hold containers when conducting low-force pull-off tests on closures and other fixings (eg. flip-cap lids).
4-pegs hold the container on an adjustable lead-screw and the knob secures the container tightly in place.…
703
Event
Wine & Spirits: Pull Tab & Twist Cap Testing
Canned wine and seltzer drinks have a clear upside that makes their popularity soar: Convenience. As well as being lighter to carry, less potentially fragile, eliminating the corkscrew, and even a glass makes it ideal for social gatherings.
704
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
705
Event
Tensile Testing: Extension, Elongation, Force & Failure
The primary objective for measuring and analyzing the the tensile force value of a product is to accurately determine one or more of these factors:
706
Event
Compression Testing in Top Load Applications
A typical challenge in packaging, and bottling applications is trying to balance product integrity, where the container might be too weak and crush under load, and excessive raw material cost, where the container is too strong.
707
Event
Webinar: Essentials of Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
708
[Page extract]
Tork testi
Tork testi, bir nesnenin döndürüldüğünde (normal çalışma sırasında veya kasıtlı olarak başarısız olana veya kırılıncaya kadar büküldüğünde) nasıl tepki vereceğini belirlemenin bir
709
[Page extract]
Torque testing
Torque testing is a way of determining how an object will react when it is being turned - during normal operation or being twisted until it deliberately fails or breaks.
710
Event
Wine & Spirits: Pull Tab & Twist Cap Testing
Canned wine and seltzer drinks have a clear upside that makes their popularity soar: Convenience. As well as being lighter to carry, less potentially fragile, eliminating the corkscrew, and even a glass makes it ideal for social gatherings.
711
[Page extract]
ASTM F1342
This test method evaluates puncture resistance of protective clothing materials which may include plastics or elastomeric films, coated fabrics, flexible materials, laminates, or textile materials.
712
Bundle
Sharps puncture tester
OmniTest 2.5
BD001
A tester designed for key international standards such as ASTM F2132, BS 7320, and BS 23907 that specify the test procedures for puncture resistance of medical sharps containers.
713
[Page extract]
ASTM F2824-10
1.1 This test method describes a method for the measurement of mechanical seal strength while separating the entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.2 This test method differs from Test Method F88.
714
Event
Fundamentals of Cork Pull & Elasticity Testing
Natural corks need to execute several important functions within the champagne and wine industries in order to meet consumers’ expectations and also to guarantee the quality of the drink.
715
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
716
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
717
Event
Understanding Top-Load Testing - Live Application Demo
Packaging manufacturers use top-load or crush testing to ensure packaging integrity, and to eliminate material excess while maintaining quality.
718
[Page extract]
What’s their secret?
“Prior to joining our class, most of our students had no actual experience with materials testing, apart from what they saw in a textbook.
719
Case study
Torque to twist out a champagne cork
Requirement
Sibel manufacture natural corks for the wine and spirits industry in the Champagne region of France. They pride themselves on working closely with their clients, taking into account their requirements and expectations for safety.
721
[Page extract]
Shear in tension
Shear testing in tension (also known as 'lap shear') is commonly used to test adhesives and involves the pulling apart of a material specimen by applying tensile force from opposite sides in a parallel plane.
722
[Page extract]
Testing Procedure
Performing the needle penetration and drag test involves several steps:
723
[Page extract]
Pull-off / Pull-out
'Pull-off' or 'pull-out' testing generally involves the separation of two secured parts under tension.
724
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
725
Case study
Cosmetics brush pull-out testing
Customised engineering example
Our client is a major cosmetics company using a variety of brushes for all applications and wished to tensile test the integrity of the bristles.