Search results
1676
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
1677
[Page extract]
ISO 8510-2
Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.
1678
[Page extract]
ASTM D2918
This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper
1679
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
1680
[Page extract]
ASTM D4476 / D4476M-14
ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.
1681
[Page extract]
29 073-3
Textiles: test method for nonwovens; Part 3: Determination of tensile strength and elongation.
1682
[Page extract]
*corp Coca-Cola SM-PR-2645
This test ensures that the column strength of non-refillable (NR) plastic bottles is sufficient to meet minimum performance specifications for vertical loading during peak load application.
1683
[Page extract]
ASTM C651
This test method covers determination of the flexural strength of manufactured carbon and graphite articles using a simple beam in four-point loading at room temperature.
1684
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
1685
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
1686
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1687
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
1688
[Page extract]
ASTM D6004-04
This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.
1689
[Page extract]
ISO 527-4
ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).
1691
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.
1692
[Page extract]
ASTM D4032-08
This test method covers the determination of the stiffness of fabrics by the circular bend procedure. The method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.
1693
[Page extract]
ISO 9727-5
Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.
1694
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
1695
[Page extract]
ASTM D7084-04
1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.
1696
[Page extract]
ASTM F1995-12
This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.
1697
[Page extract]
CETIE Guide 18
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
1698
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
1699
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
1700
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.