Mecmesin | Search results

1451

^{[Page extract]}

ISO 8510-1

Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.

1452

^{[Page extract]}

BS EN 1393

BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.

1453

^{[Page extract]}

BS EN ISO 8670-2

Two part test on filled bags: 1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate

1454

^{[Page extract]}

ASTM D2659

ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.

1455

^{[Page extract]}

ISO 594-2

ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.

1456

^{[Page extract]}

PSTC 8

Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape. The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.

1457

^{[Page extract]}

FINAT FTM2

This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.

1458

^{[Page extract]}

BS EN ISO 11608-3

Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions

1459

^{[Page extract]}

ASTM D3410 / D3410M

ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.

1460

^{[Page extract]}

BS EN 12316-1

Waterproof materials, Sheet materials, Flexible materials, Peel resistance, Peeling tests, Joints, Bitumens, Bituminous products, Roof coverings, Test equipment, Specimen preparation

1461

^{[Page extract]}

BS EN 12346

Gymnastics equipment, Wall bars, Ladders, Sports equipment, Indoor sports equipment, Design, Dimensions, Height, Dimensional tolerances, Shape, Strength of materials, Safety measures, Marking, Instructions for use, Equipment safety, Mechanical testing,

1462

^{[Page extract]}

BS ISO 14488

(Method A used for shotcrete testing.)

1463

^{[Page extract]}

ISO 7810

Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.

1464

Case study

การทดสอบปุ่มแดชบอร์ด

ความต้องการ Visteon ต้องการระบบอัตโนมัติในการวัดแรงกระตุ้นสำหรับปุ่มแดชบอร์ดและตรวจสอบจุดปิดหน้าสัมผัสไฟฟ้า ด้วยการหาจำนวนความรู้สึกส่วนตัวของปุ่มพวกเขาจะสามารถปรับปรุงความรู้สึกที่มีคุณภาพได้ เนื่องจากโหลดที่วัดได้ต่ำมากโดยทั่วไปจะน้อยกว่า 10N

1465

^{[Page extract]}

ASTM D1321

This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.

1466

^{[Page extract]}

BS EN 1719

Adhesives, Adhesive strength, Adhesion tests, Paper, Board (paper), Pressure-sensitive materials, Testing conditions, Mathematical calculations

1467

^{[Page extract]}

ISO 1798

ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks. This test standard is equivalent to BS EN ISO 1798:2008

1468

^{[Page extract]}

IEC 61196-1-308

IEC 61196-1-308:2012(E) applies to coaxial communication cables. It specifies test methods for tensile strength and percentage elongation at fracture for annealed and hard-drawn solid copper clad metals to be used as inner conductor for coaxial cables.

1469

^{[Page extract]}

ISO 505

ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.

1470

^{[Page extract]}

ISO 813

ISO 813 specifies a method for the determination of the adhesive strength of a vulcanized or thermoplastic rubber bonded to a rigid substrate, using a test piece comprising a strip of rubber bonded to a single plate of rigid material.

1471

^{[Page extract]}

ASTM E1820-18ae1

The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.

1472

^{[Page extract]}

ISO 12625-4

Specifies a test method for the determination of the tensile strength, stretch at break and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.

1473

^{[Page extract]}

ISO 11339

ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.

1474

^{[Page extract]}

ASTM D2370

This test method covers the determination of the elongation, tensile strength, and stiffness (modulus of elasticity) of organic coatings when tested as free films.

1475

^{[Page extract]}

BS EN ISO 10619-1

BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.