Mecmesin | Search results

1376

Case study

การทดสอบการดึง Diamante

ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับ Marks & Spencer ผู้ค้าปลีกเสื้อผ้ารายใหญ่ในสหราชอาณาจักรซึ่งกำหนดว่าจะต้องมีการทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมด

1377

^{[Page extract]}

Mountaineering equipment, Outdoor sports equipment, Sports equipment, Safety measures, Equipment safety, Tape, Webbing, Tensile strength, Stability, Weight measurement, Marking, Test specimens, Testing conditions

1378

^{[Page extract]}

ASTM D622-99

ASTM D622 is a test method intended for use in testing the conventional types of hose employed for the operation of air brake and vacuum brake systems, either on a single motor vehicle or as connecting or transmission lines in a combination of vehicles<

1379

^{[Page extract]}

ASTM D3658

This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.

1380

^{[Page extract]}

BS EN 12242

The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g

1381

^{[Page extract]}

ASTM D3106

This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.

1382

^{[Page extract]}

ASTM D5587-08

This test method covers the measurement of the tearing strength of textile fabrics by the trapezoid procedure using a recording constant-rate-of-extension-type (CRE) tensile testing machine.

1383

Case study

การทดสอบการดึงโบว์ติดเสื้อผ้า

ความต้องการ ลูกค้าเป็นซัพพลายเออร์ให้กับ Marks & Spencer ผู้ค้าปลีกเสื้อผ้ารายใหญ่ในสหราชอาณาจักรซึ่งกำหนดว่าต้องทดสอบตัวยึดและสิ่งที่แนบมาทั้งหมดว่าล้มเหลว

1384

^{[Page extract]}

ISO 13935-1

ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.

1385

^{[Page extract]}

ASTM D2633

ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.

1386

^{[Page extract]}

ISO 17454

ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.

1387

^{[Page extract]}

BS EN 2597

BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics. Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.

1388

^{[Page extract]}

ISO 6922

Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.

1389

^{[Page extract]}

FEFCO 4-6,8,11,50,55

Older standards and international replacements used for:

1390

^{[Page extract]}

ASTM D926-17

ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.

1391

^{[Page extract]}

ASTM C297

This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.

1392

^{[Page extract]}

ASTM F36-15

The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.

1393

^{[Page extract]}

ASTM D3163

ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.

1394

^{[Page extract]}

ASTM D3983

This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.

1395

^{[Page extract]}

EN 826

Compression strength, deformation, deformation after 10% of compression.

1396

^{[Page extract]}

ASTM D575-91

These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.

1397

^{[Page extract]}

ASTM F2132-01

This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.

1398

^{[Page extract]}

BS EN 2591-418

Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.

1399

^{[Page extract]}

BS EN 1895

Adhesives, Adhesion tests, Peeling tests, Paper, Paper products, Board (paper), Disposable, Packaging materials, Flexible materials

1400

^{[Page extract]}

BS EN 50289-3-2

Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Tensile testing, Tensile strength, Elongation, Electric conductors