Mecmesin | Search results

1426

^{[Page extract]}

ISO 8009

ISO 8009:2004 specifies the minimum requirements and test methods to be used for reusable diaphragms made from natural rubber and silicone rubber. These diaphragms are intended for contraceptive use.

1427

^{[Page extract]}

ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.

1428

^{[Page extract]}

BS 6319-2

BS 6319-2 is a test method for determining the compressive strength of resin and polymer/cement compositions used in construction.

1429

^{[Page extract]}

ASTM D2731

ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.

1430

^{[Page extract]}

BS EN ISO 22254

ISO 22254:2005 specifies a test method for determining the resistance of the tufted portion of manual toothbrushes to deflection. This could be used to derive a stiffness - a factor which has been of great concern to consumers and manufacturers.

1431

^{[Page extract]}

ISO 10354

Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.

1432

^{[Page extract]}

BS ISO 11752

BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.

1433

^{[Page extract]}

TAPPI T 576

This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.

1434

^{[Page extract]}

ISO 188

ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:

1435

^{[Page extract]}

Tension

There are in essence two types of tensile grips:

1436

^{[Page extract]}

*corp 01M-01-309

To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.

1437

^{[Page extract]}

BS EN 455-2

Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing

1438

^{[Page extract]}

ASTM C1341

This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.

1439

^{[Page extract]}

BS EN ISO 6892-1

This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.

1440

^{[Page extract]}

ASTM D7249-12

This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the

1441

^{[Page extract]}

ASTM E2658-15

These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices

1442

^{[Page extract]}

USP <381>

This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.

1443

^{[Page extract]}

ASTM F543-13

This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.

1444

^{[Page extract]}

ASTM D413-98

ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.

1445

^{[Page extract]}

BS EN 17394-2

This document defines a test method for security of attachment of functional and decorative buttons to clothing including garments such as gloves, hats, scarves, hosiery, ties, and textile belts. The scope of this document is limited to sewn-on buttons,

1446

^{[Page extract]}

ISO 4049

This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or

1447

^{[Page extract]}

ASTM D4776 / D4776M-18

ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.

1448

^{[Page extract]}

ASTM D6534-05

This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.

1449

^{[Page extract]}

ISO 29862

This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.

1450

^{[Page extract]}

ASTM D6264 /D6264M-17

In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force