Mecmesin | Search results

1401

^{[Page extract]}

ASTM D5467 / D5467M-97

ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.

1402

^{[Page extract]}

FINAT FTM3

This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.

1403

^{[Page extract]}

ASTM D3968

This test method covers the measurement of rotational torques of Type IIIA child-resistant closures as a means of monitoring normal functioning of the child-resistant package.

1404

^{[Page extract]}

ASTM F806-99a

ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.

1405

^{[Page extract]}

ASTM D5321-12

This test method covers a procedure for determining the shear resistance of a geosynthetic against soil, or a geosynthetic against another geosynthetic, under a constant rate of deformation.

1406

^{[Page extract]}

A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature

1407

^{[Page extract]}

Tack test

1408

^{[Page extract]}

ISO 21180

ISO 21180 specifies a test method for the determination of the maximum tensile strength of light conveyor belts.

1409

^{[Page extract]}

ASTM D1710

Among tests for electrical and dimensional (temperature) stability, includes methods for tensile characteristics.

1410

^{[Page extract]}

ASTM D3471

This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.

1411

^{[Page extract]}

NF S86-604

This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.

1412

^{[Page extract]}

ASTM D2344 / D2344M

ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.

1413

^{[Page extract]}

ASTM D6713-14

Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro

1414

^{[Page extract]}

ASTM D3826

ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.

1415

^{[Page extract]}

ISO 8510-2

Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.

1416

^{[Page extract]}

BS EN ISO 13262

BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.

1417

^{[Page extract]}

ASTM D4476 / D4476M-14

ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.

1418

^{[Page extract]}

BS EN ISO 22088-2

BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics. This has replaced BS EN ISO 6252:1998

1419

^{[Page extract]}

SAE J1525

This SAE Recommended Practice describes a lap shear test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber reinforced plastics to themselves and to metals.

1420

^{[Page extract]}

ISO 9073-3

Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.

1421

^{[Page extract]}

TAPPI T 807

This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).

1422

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

1423

^{[Page extract]}

BS EN 12209

BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.

1424

^{[Page extract]}

ASTM E855-08

This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.

1425

^{[Page extract]}

CETIE Guide 18

This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.