Search results
1526
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
1527
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
1528
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
1529
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
1530
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
1531
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1533
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
1534
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
1535
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
1536
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
1537
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
1538
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
1539
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1540
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
1541
[Page extract]
ASTM E405-04
These tests provide standard methods for evaluating the mechanical performance of the rotary-type window operators, while the operators are subjected to cyclic wear in opening and closing against the operating moment.
1542
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
1543
[Page extract]
ASTM D4562-01
This test method covers the determination of the shear strength of curing liquid adhesives used for retaining cylindrical assemblies or for locking and sealing threaded fasteners.
1544
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
1545
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
1546
[Page extract]
ASTM D6496-04a
This test method covers the laboratory determination of the average bonding strength between the top and bottom layers of a sample of a geosynthetic clay liner.
1547
[Page extract]
BS EN 1271
Balls (sports equipment), Ball-games equipment, Sports nets, Dimensions, Design, Classification systems, Performance, Breaking load, Yarn, Cords, Grades (quality), Safety measures, Mechanical testing, Instructions for use, Marking, Foundations, Anchorag
1548
[Page extract]
BS EN ISO 10074
Aluminium, Aluminium alloys, Coated materials, Anodizing, Anodic coating, Coatings, Thickness, Density, Surface defects, Classification systems, Oxides, Inspection, Grades (quality), Wear resistance, Hardness, Corrosion resistance, Wear tests, Specimen
1549
[Page extract]
ASTM D6797-07
This test method describes the measurement for bursting strength of woven and knitted textiles taken from rolls of fabric or fabric taken from garments.
1550
[Page extract]
ASTM D1894
This test method is used to measure the friction of plastic film and sheeting. It determines the kinetic (moving) and static (starting) resistance of one surface being dragged across another.