Mecmesin | Search results

1301

^{[Page extract]}

BS EN ISO 1856

BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.

1302

^{[Page extract]}

ISO 8627

Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.

1303

^{[Page extract]}

SAE J 1907

This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.

1304

^{[Page extract]}

BS ISO 3597-2

ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.

1305

Specials

Thermal cabinet environment chamber

Environmental chamber capability Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.

1306

^{[Page extract]}

ASTM D7264 / D7264M-15

ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:

1307

^{[Page extract]}

FINAT FTM1

This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.

1308

^{[Page extract]}

ASTM D3914

ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.

1309

^{[Page extract]}

BS EN ISO 376

BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.

1310

^{[Page extract]}

Three flavours of confectionery test

What makes the confectionery sector’s products particularly sensitive to ingredient substitutions?

1311

^{[Page extract]}

ASTM D1995

These test methods cover procedures by which autohesives can be tested in four commonly practiced stressing modes, namely: compression shear, cleavage, climbing drum peel, and T-peel, and in various combinations of rigid-to-rigid, flexible-to-rigid, and

1312

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1313

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1314

^{[Page extract]}

ASTM D6195-03

These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.

1315

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1316

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1317

^{[Page extract]}

SAE J174M

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.

1318

^{[Page extract]}

BS EN 1492-1

Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web

1319

^{[Page extract]}

ASTM B913

This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.

1320

^{[Page extract]}

BS EN 1465

Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.

1321

Case study

경찰 수동 취급 및 보호 복

요구 사항 영국의 주요 경찰은 모든 신병이 'Job Related Fitness Test'(JRFT)를 통과하여 역할에 대한 부담스러운 신체적 요구를 충족 할 수 있도록 요구합니다. 무장 장교는 매년 재평가를 받아야합니다. College of Policing은 평가 시험에서 잉글랜드와 웨일즈 경찰에 지침을 제공합니다. 개별 부대는 자신의 체력 평가를 위해 이러한 지침을 보강 할 수 있습니다.

1322

^{[Page extract]}

ASTM D1871

This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.

1323

^{[Page extract]}

ASTM D380

ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.

1324

^{[Page extract]}

ISO 8510-1

Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.

1325

^{[Page extract]}

BS EN 1393

BS EN 1393 specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.