Mecmesin | Search results

1276

^{[Page extract]}

ISO 527-5

ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.

1277

^{[Page extract]}

BS 2782-3: 360C

BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method

1278

^{[Page extract]}

Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.

1279

^{[Page extract]}

BS EN 12814-2

BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.

1280

^{[Page extract]}

BS EN 12467

Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio

1281

^{[Page extract]}

Consumer Products

Mecmesin test solutions for products typically found in the home ...

1282

^{[Page extract]}

ASTM D876 - 13

ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.

1283

^{[Page extract]}

VectorPro test definition

https://ahpublic.s3.eu-west-2.amazonaws.com/VectorPro/vcs/export/live/v…

1284

^{[Page extract]}

ASTM F36-15

The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.

1285

^{[Page extract]}

ASTM D3163

ASTM D3163 is a test method used to determine the single-lap shear adhesive joints of rigid plastic adherends. The test method is useful for generating comparative shear strength data for joints made from a number of plastics.

1286

^{[Page extract]}

ASTM D3983

This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.

1287

^{[Page extract]}

ASTM F1044-05

This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures.

1288

Event

Advanced Engineering 2021 - We would love to see you there!

Who should attend? Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions. What is the exhibition about?

1289

^{[Page extract]}

EN 826

Compression strength, deformation, deformation after 10% of compression.

1290

^{[Page extract]}

IEC 60371-2

Part 1 is definitions of general requirements Part 3 specifications for individual materials A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.

1291

^{[Page extract]}

ASTM C203

ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.

1292

^{[Page extract]}

ASTM D6195-03

These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.

1293

^{[Page extract]}

ISO 12236

Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.

1294

^{[Page extract]}

ISO 7886-4

This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design

1295

^{[Page extract]}

SAE J174M

This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.

1296

^{[Page extract]}

BS EN 1492-1

Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web

1297

^{[Page extract]}

ASTM F607-03

The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.

1298

^{[Page extract]}

ASTM D5656-10

This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.

1299

^{[Page extract]}

BS EN 50289-3-17

Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths

1300

^{[Page extract]}

ISO 1926

ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.