Search results
1701
[Page extract]
BS EN 3841-509
This standard specifies a method of determining the forces required to insert and extract the contact pin into and out of the terminal socket of the signal contact. It shall be used together with EN 3841-100.
1702
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
1703
[Page extract]
BS EN 862
Packaging. Child resistant packaging. Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products
1704
[Page extract]
BS ISO 6939
Applicable to spun single and folded yarns of any fibre or mixture of fibres manufactured by any spinning systems. Not recommended for testing filament yarns, glass yarns, more complex structures such as cabled yarns or cords.
1705
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
1706
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of
1707
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
1708
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
1709
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
1710
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
1711
Article/Campaign
Test title
Tensile Testing Solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
1713
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
1714
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
1715
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1716
[Page extract]
CETIE Guide 2
This guide applies to the screw capping of non-carbonated beverages and products with a metallic tamper-evident closure. Bottles may also be fitted with an in-bore insert for product flow control or to prevent re-filling.
1717
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
1718
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.
1719
[Page extract]
ASTM D4760-91
This test method determines the proper resecuring of continuous thread child-resistant closures.
1720
[Page extract]
ASTM D5528-13
ASTM D5528 is a test method, which determines the opening Mode I interlaminar fracture toughness of continuous fiber-reinforced composite materials. It uses a a double cantilever beam (DCB) specimen. Susceptibility to delamination is one of the major
1721
[Page extract]
ASTM D2534
The coefficient of friction is related to the slip properties of many commercial articles that have been coated with petroleum wax (for example, butter cartons and wax-impregnated or hot melt coated corrugated board).
1722
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
1723
[Page extract]
ASTM D1894
This test method is used to measure the friction of plastic film and sheeting. It determines the kinetic (moving) and static (starting) resistance of one surface being dragged across another.
1724
[Page extract]
ASTM D6746-15
ASTM D6746 is a test standard that covers methods to evaluate a characteristic of raw rubber or unvulcanized rubber compounds that is designated as green strength.
1725
[Page extract]
BS EN 12445
This standard specifies the test methods to be applied to a power operated door to demonstrate compliance with the requirements specidied in EN 12453: 2000 in particular it specifies the method of measuring the forces developed by a power operated door.