Mecmesin | Search results

1651

^{[Page extract]}

BS EN 1394

BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.

1652

^{[Page extract]}

ISO 9727-5

Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.

1653

^{[Page extract]}

This test method covers the determination of the stiffness of fabrics by the circular bend procedure. The method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.

1654

^{[Page extract]}

ISO 9073-3

Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.

1655

^{[Page extract]}

ASTM D7084-04

1.1 This test method covers the determination of bulk crush strength of a bed of formed catalyst particles 1⁄32 to 3⁄16 in.

1656

^{[Page extract]}

CETIE Guide 9

This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on

1657

^{[Page extract]}

ASTM D3916

ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.

1658

Article/Campaign

Test title

Top-load testing solutions

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.

1659

^{[Page extract]}

ASTM D5618-94

This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.

1660

^{[Page extract]}

*corp Ford DSEU

Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.

1661

^{[Page extract]}

EN 149

EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.

1662

^{[Page extract]}

ISO 9895

Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.

1663

^{[Page extract]}

ASTM D1004

ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.

1664

^{[Page extract]}

ASTM D3575

ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.

1665

^{[Page extract]}

BS ISO 7322

This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells

1666

^{[Page extract]}

ASTM C480

This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.

1667

^{[Page extract]}

*corp Ikea IOS-TM-0057

This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations

1668

^{[Page extract]}

ASTM D3469

These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.

1669

^{[Page extract]}

SAE J 1553

This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.

1670

^{[Page extract]}

Vice grip (Mechanical)

Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.

1671

^{[Page extract]}

TAPPI T 840

This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.

1672

^{[Page extract]}

ASTM F1304-18

ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.

1673

^{[Page extract]}

Special compression fixtures

Special compression fixtures have been specially designed to meet the challenges of a particular application.

1674

^{[Page extract]}

ISO 527-3

ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.

1675

^{[Page extract]}

ASTM E405-04

These tests provide standard methods for evaluating the mechanical performance of the rotary-type window operators, while the operators are subjected to cyclic wear in opening and closing against the operating moment.