Search results
1426
[Page extract]
ASTM D7249-12
This test method covers determination of facing properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes and result in compressive and tensile forces in the
1427
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
1428
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
1429
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
1430
[Page extract]
ISO 16047
ISO 16047:2005 specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.
1431
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
1432
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
1433
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1434
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
1435
[Page extract]
ASTM C403/C403M
This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
1436
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
1437
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
1438
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
1439
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
1440
[Page extract]
ISO 8009
ISO 8009:2004 specifies the minimum requirements and test methods to be used for reusable diaphragms made from natural rubber and silicone rubber. These diaphragms are intended for contraceptive use.
1441
[Page extract]
ISO 10373-1
ISO/IEC 10373-1:2006 specifies the non-technology-specific test methods required to establish conformance of identification cards to the base (requirements) standards, for which the fundamental properties are defined in ISO/IEC 7810.
1442
[Page extract]
ASTM D2731
ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.
1443
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
1444
Article/Campaign
Test title
Tensile Testing Solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
1445
[Page extract]
BS EN ISO 22254
ISO 22254:2005 specifies a test method for determining the resistance of the tufted portion of manual toothbrushes to deflection. This could be used to derive a stiffness - a factor which has been of great concern to consumers and manufacturers.
1446
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
1447
[Page extract]
ASTM D751-06
These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products.
1449
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given: